1979 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Assemble
Instructions from Wireless BLE Kinesis Advantage (Custom Controller)
I tried to label all the parts on the PCB and everything lines up so it should be pretty easy. If you're having trouble soldering the pins on the flex connectors, get a better iron! I upgraded to a fx-888 and my soldering time for the board went...

Final Wreath Assembly
Instructions from Arduino Advent Wreath
The most fun part was taking the circuit and wrapping pipe cleaners around everything. I put the PCB in the middle of the green circle, made sure that the candle pipe cleaners were in place, and used some other pipe cleaners for attaching the PCB to...

Assembly
Instructions from CastVolumeKnob
3D print the case and glue the middle and the top part togetherSolder everything to the PCBPut the LED ring and Encoder in placeScrew the Board in placeSolder the Battery holder to the charging/boost converter boardGlue it in placeScrew the bottom part...

The completed board
Instructions from 5-12V Capacitive Touch Switch
Here is the finished PCB after cooling down. 5 on 6 without problems. After soldering on the slipped diode,, I checked the solder joints again with a microscope. Everything looks good so far.

Carefully re-assemble
Instructions from Tiller Autopilot Limit Switches
Replace the controller PCB and check all its connectors are seated properly.Check again that there are no pinched wires and that everything can move freely.replace the watertight seal, clean and grease this with silicone grease if needed.Replace the...

Put Everything Back Together and Connect the MP3 Module, Cat Feeder PCB Override and Motion Detector to the Raspberry Pi
Instructions from Magic Flute of Rat Mind Control w/ Raspberry Pi
The automatic cat feeder PCB, DFPlayer module and motion detector should be connected to Raspberry Pi as directed above. You don't need to power the feeder PCB and everything else runs on 5v so just connect the motion detector and DFPlayer to the 5v...

JudgeTron 9001
Instructions from JudgeTron 9001
Okay, what does a JudgeTron need? My idea was to use neural networks embedded in biological units to do the whole judging thing. These biological units unfortunately don't have native electrical interfaces: I couldn't just put a RJ45 into them and have...

PixiFlood
Instructions from PixiFlood
Solder: WS2811S (IC2) to PCB. Same warnings as the PT4115B.That is the last of the SMT/SMD components, everything from this point forward is Plated Through Hole (PTH).Stage 1 Assembly is complete. At this point you are ready to conduct the first series...

Portable environmental monitor
Instructions from Portable environmental monitor
Populate the board. You will need some good experience with 0805 SMD soldering, and some tools like soldering iron and hot air rework station. Start with the bottom side, with the microcontroller, the other ICs and finally the small passive components....

Materials Needed
Instructions from SIGHT: For the Blind
Here are the components and materials that you needed to do this project. Take your time and collect everything! Main Components: Raspberry Pi 3 Raspberry Pi Camera Module(5 Mp) Micro Push Button 1K Resistor General Purpose PCB Tools: Soldering iron...

Electronic
Instructions from GRawler - Glass Roof cleaning crawler
The electronic part can be soldered to a breadboard. See the attached schematic for detail. I also attaches the eagle sch-file if you like to make your own pcb. To protect the electronic from moisture, everything including the batteries can be built...

Mount PCB In Modified Enclosure
Instructions from Hacking a $35 ECG nRF52 Fitness Tracker into EEG
Fitting all the wires in their assigned holes.... I trim down the electrode wires for soldering. Test to see if everything fits inside the enclosure when the cap is fixed on top. The cap and enclosure body should fit together without any pressing or...

Drilling Part I
Instructions from Ender 3 PCB Drilling
Place the PCB to be drilled on top of a cardboard sheet (it doesn't need to be thick, mine is 1mm), which goes on top of the Ender 3 printing table. Hold everything with clamps on the corners. Alternatively, you might use double-sided stick tape.Manually...

Make sure everything still fits
Instructions from FC3000 Headphone jack mod
Make sure the connector fits after soldering the wires. Try to put the PCB on top, there should be some room to move the connector, if after putting the PCB the connector can't be moved, it's too thick. Either you bent the pins the wrong way or you put...

Putting It All Together
Instructions from Ariadne Headband
Now its time to program arduino, you can find arduino program in our Gitlab repository which we have linked in our project site. Next connect headband and power pin header connector, pay attention to right orientation and switch the power button. While...

|<
<
1
2
3
4
5
>
>|