Close

1979 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • gadget-case
  • Instructions     from gadget-case
  • We'll start with the base piece because it's easier. Download the "gadget-case_base.dxf" file, and adjust it for the kerf of your laser. In the DXF file, the holes are exactly 3 mm diameter. We're going to tap for M3, so you need to reduce the diameter...

  • DIY RaspCade
  • Instructions     from DIY RaspCade
  • 5. SoftwareRetroPieThis part is pretty straight forward, we will simply be installing RetroPie on the Pi and configuring our controls one the first boot. Thanks to the Picade PCB, all buttons are detected as keyboard inputs, so when RetroPie first boots,...

  • Accelerated Dice
  • Instructions     from Accelerated Dice
  • HardwareThe assembly of components is pretty straightforward, although it would be easier with a proper PCB. Below is a diagram showing the pinouts of the three devices. They are all well marked although its not clear right off the bat which Trinket...

  • Build the PCB
  • Instructions     from Belle: Door bell alert with ESP8266 + IFTTT
  • Note: Do not connect the batteries yet! Download the KiCad filesGenerate the GERBER files or download themManufacture the PCBOrder the Bill of MaterialsSolder the parts on the PCBDo a continuity test Use the test firmware to ensure everything is...

  • Soldering the microphone
  • Instructions     from Repairing the microphone of an LG G3
  • At first I tried to put some soldering paste on the pads and solder it on it's place like a normal SMD-component or like it was originally but I couldn't make it work in this way. So I stripped some cables and took those thin wires to make a connection...

  • Glowstick kinetics
  • Instructions     from Glowstick kinetics
  • Build a linear CCD module (SPI-version)The 3D-printed CCD-box is for the LDO-version PCB (but the LDO part of the circuit does not necessarily need to be populated). Install a 1x6 pin header on the back of the board. [picture coming]Print everything...

  • Modifying VMU Case
  • Instructions     from VMU Zero V2 [coming soon]
  • Tools Screw DriverSide Plier7mm Flat FileXACT KnifeAir Duster Disassemble VMU Strip down the VMU and keep everything but the PCB, coin cell and display.Try not to touch the piezo speaker to prevent fingerprints on the disc. Modify Case Use plier and...

  • Assemble the oscillator module
  • Instructions     from PolyMod: modular digital synthesizer
  • Now that you have the master module, you need another module which can connect to it. The most obvious choice is an oscillator module, because it will produce a waveform which you will be able to hear, allowing you to test that everything is working...

  • Ordering Parts
  • Instructions     from Nomad
  • There are three kinds of processors that are compatible with the Nomad board, all of which are slightly different: The 68000 is the "classic" 68000 processor.  This processor draws more power than the 68HC000, and cannot be clocked as fast. ...

  • Microcontroller assembly
  • Instructions     from HEGduino
  • This part is fairly self explanatory as everything is clearly labeled. First add the 2.7kOhm resistor and the ADS1115. The ADS1115 has clearly marked VDD and A0 pins to indicate the direction it should be placed on the hub board. Clip the leads to make...

  • Ordering the PCB
  • Instructions     from Backup Power Supply for Proper Shutdown
  • After the design is complete it's time to order the PCB. To so we used the sponsor of this article JLCPCB.com JLCPCB are also sponsor of this project. JLCPCB (Shenzhen JLC Electronics Co., Ltd.), is the largest PCB prototype enterprise in China...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday