3515 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

The HYDRA multiheaded virtual computer
Instructions from The HYDRA multiheaded virtual computer
Gather parts to build a system for your intended purpose:Research your system board & processor & be double or more sure it is supported. Number of PCIe, PCI should reflect what you want to run. Internal serial HEADER is preferable over DB9 on...

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
Axial Components:Were going to start with the polarized components theses only function in the correct orientation. The way to determine the way the go is simple, look for the band around the diode in theses case it is black. Match the band the the symbol...

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
This is the MOV it provides some basic surge supression.

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
Green indicator leds D1 D2 (near fuse holder) D6 D7(at the top right.) Leds are polarized you need to get them the right way around, look at the symbol on the pcb it shows a circle with a flat side. Match that flat edge to the flat edge on the led.These...

A 25 cent Phone to Microscope Adapter
Instructions from A 25 cent Phone to Microscope Adapter
To hold the iPhone into the foam block, I routed a pocket the same size as theiPhone into the top of the block. Normally, I would have routed the holea little bit larger than the phone to ensure that it would fit, but by making the pocket the same size,...

Pressure Cooker Vacuum Chamber
Instructions from Pressure Cooker Vacuum Chamber
Step 2: Prepare the pressure cookerNow for the fun part. In this step, you'll be drilling a hole in your nice shiny new pressure cooker. I know, it's tough, but it's for a good cause.You're going to need: A metalworking drill pressThe pressure cookerA...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

HPDL watch
Instructions from HPDL watch
Let's start with PCB. I wanted to mound display on one side of the PCB and the uc - on the other. Unfortunatelly, uc barely fits in the middle of the display's back and some pinout traces of display and uc touches where they mustn't. The traces...

HPDL watch
Instructions from HPDL watch
Add a battery holder and upload the firmware. I had a holder which was designed for thinner battery than CR2450. I wanted to bend it's top pin but I broke it, so I had to make it from wire. By the way, I had to extend the gap between it's pins...

HPDL watch
Instructions from HPDL watch
Make a whristlet:It is very easy. You can see holes on my manufactured PCB. I just mounted screws through them and bent 2 pieces of wire like in the foto which can be placed on those screws over cut off gaps of PCB. The whristband itself is made...

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Putting it all together.This is fairly easy beacuz you just have to conect some wires and do some solderin job for the cat 5 cable and nothing else

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Somthing extraOright so you wana get a littl bit bigger with you camera and wan make a night vision one you can get IR Led Ring from Ebay,Amazon.Or you can make one your self get a protoboard and get some 10mm IR Led and make a your self IR Led ring...

FireCoates
Instructions from FireCoates
Jacket Wiring, LED Setup, and Light Pipe Assembly.I never took pictures of this process with the first prototype so I need to complete the second prototype and take pictures to use as visual aides along the way, I should have them up in another week...

FireCoates
Instructions from FireCoates
Optional 3D Printed Jacket Module CaseDownload the Base and Top to the case and print them on your favorite RepRap OpenSource 3D Printer. It should come out looking similar to this(colors may vary ;) ):The headphone jack hole may need to be cleaned up...

Modular cartesian machines
Instructions from Modular cartesian machines
Here can see how ensamble it. And how to keep the paper in place with some binder clips.

|<
<
5
6
7
8
9
>
>|