603 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》텐하드룸ぉぅvictorious≒텐하드레깅스룸텐하드레깅스◀texas 텐하드선릉텐하드 텐하드룸セ텐하드룸⇒like㎂"

Install the Hyperpixel 4.0 driver for the display
Instructions from ORPI
Described here in the Pimoroni documentation:curl https://get.pimoroni.com/hyperpixel4 | bashI did this connected via ssh like described in step 5

Yet Another (PiZero) Wi-Fi 'Hat'
Instructions from Yet Another (PiZero) Wi-Fi 'Hat'
Now a quick change to one of the files. The driver will fail to compile: nano +567 wilc1000/wilc_wfi_cfgoperations.cYou should see something like this:cfg80211_disconnected(dev, pstrDisconnectNotifInfo->u16reason, pstrDisconnectNotifInfo->ie, pstrDisconnectNotifInfo->ie_len,...

Hydra Multi OS Gaming Console & Controller
Instructions from Hydra Multi OS Gaming Console & Controller
6) Test passthroughYou should now have a Win7 VM installed. Testing Passthrough is easy: Install VMware ToolsJust select "install/Upgrade VMware Tools" in the console menu (while the machine is powered on)Follow the prompts & take all the defaultsInstall...

NESPi Controller
Instructions from NESPi Controller
Run "sudo ~/RetroPie-Setup/retropie_setup.sh"Configure Wi-Fi under Setup/Configuration if you are using a Wi-Fi adapter.Enable the gamecon GPIO driver. It should appear under the Setup/Configuration menu. It will ask you if you want to enable the configuration...

How to flash
Instructions from Hakko revenge
- Keep the soldering station externally powered via the DC connector - Connect your MSP launchpad to the usb port of your computer - Connect the flashing cable like in the above image - Run IAR embedded workbenck - Click Project/ Options/Debugger to...

Build instruction
Instructions from Single-hand GPIO Clock
The wiring diagram is pretty self-explanatory. Connect motor driver and opto-fork power inputs to Raspberry Pi 5V. (This assumes that your motor uses less than 500mW of power, and can run on 5V, like the listed motor. Also assumes that your opto-fork...

▇▇▇▇ Key Point #1: Does Verilog Execute Like Software? ▇▇▇▇
Instructions from FPGA Bootcamp #1
(Note: now we are going to start working on the Adder. You can download the source from the file section or follow along in the online simulator). Verilog isn't executable in the same way that C or Python code is (except when it is). That’s...

Solving the conflict with ups_yec
Instructions from Link an old UPS to a QNAP NAS
This leaves us with a few options: Change the Arduino’s FTDI VendorID/ProductID (you’d need to apply to the FTDI manufacturer for it and prepare driver deployment of some kind) Remove or disable ups_yec in some way (there are scripts that control...

Solder paste stencils on Windows 7
Instructions from Solder paste stencils on Windows 7
There is a lot you can read about USB difficulties on Windows and how to make it work. But the TL;DR is to download Zadig for Windows Vista or later as suggested on the LibUSB wiki page. Start Zadig (there is no install), "Options/List All Devices",...

NixieBot
Instructions from NixieBot
Before you embark on a project like this you should first make sure you can obtain the B7971 nixie tubes, these are becoming quite rare now and attracting high prices. It might take you a few months to track down enough, though you can start with as...

Stepper mounted driver
Instructions from Stepper mounted driver
Tin the copper and driver.After you got them well covered, remove as much solder as you can from your tinning... Heating them up and dropping them works well. Don't overheat the driver too much or you could loose components on the other side..Now would...

thingSoC NEOLED : NEOPixels on Intel Edison
Instructions from thingSoC NEOLED : NEOPixels on Intel Edison
Reprogramming the TSOC_NeoLED Driver BoardIf you need to update the firmware in the TSOC_NeoLED board, or load your own custom firmware, you can use a USB to UART adapter, like the FTDI basic (the little red board) shown below:To reprogram the TSOC_NeoLED...

Soldering
Instructions from Xbox One X Laptop
Due to the nature of the Xbox motherbaord, you will need a 150 watt soldering iron (pencil style) to do this smoothly. I highly recommend the JBC DDE-1B. Most hobbyist-grade irons don't have enough power. Tie the power supply to the mother board...

Adding an external relay for the second circuit (optional)
Instructions from Sonoff Mini dual switch support
If you happen to need another relay (or an electrical output for something else) for the new switch instead of just sending state changes over MQTT, you sure can, it's your device. To make it more convenient and reliable, we chose the GPIO1 with its...

BUYING THE PARTS
Instructions from Making the Ultimate Class-E Musical Tesla Coil
WARNING: DO NOT PURCHASE IMPORTANT COMPONENTS LIKE MOSFET’S OR DRIVER IC’S FROM GENERAL SHOPPING WEBSITES LIKE AMAZON OR EBAY! MANY PEOPLE HAVE PURCHASED CIRCUIT COMPONENTS FROM SUCH SITES AND FOUND THEY WERE TOTALLY USELESS. DON’T WASTE YOUR MONEY:...

1
2
3
4
5
>
>|