603 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ《〈 문의 OIO↗5793↗7458 》〉㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

PixiFlood
Instructions from PixiFlood
Solder remaining resistors 4.7K to PCB, The 4.7K ohm resistors I have begun to solder on the bottom of the PCB. Due to the nature the ceramic coating it isolates the driver from the flood body and provide support to ensure that the though leads do not...

PixiFlood
Instructions from PixiFlood
Driver at this point:The next steps are Optional Depending on Needs:Optional 1: Verify the clearance between any connectors you may be using and the reflector before soldering to the PCB. Also check clearance of the floodlight body. If an issue exists...

PixiFlood
Instructions from PixiFlood
You now have a fully tested driver board that is ready for the LED to be attached.I had previously recommended a "tin" process which I have now replaced with the process outlined in the youTube video which can be found here:The new process should be...

PixiFlood
Instructions from PixiFlood
FINAL ASSEMBLY:Be sure to test the LED Driver before installing it in the floodlight body. This is accomplished by supplying 12V power and a WS2811 data stream.If there are any issues, review each solder joint ensuring that it is not a "Cold" joint and...

PixiFlood
Instructions from PixiFlood
Attach the combined LED and driver module to the floodlight body using the screws removed during the remove step above. ((The pictured driver is a V1.6 which nobody received. These pictures are only intended to give you an idea of the placement. I will...

ARDUINO MPPT SOLAR CHARGE CONTROLLER
Instructions from ARDUINO MPPT SOLAR CHARGE CONTROLLER
This project is consists of 40 steps.So for simplicity I divided the entire project in to small sections.Click on the link which you want to see.1. Basics on MPPT charge controller2. Buck circuit working and design calculation3. Testing the Buck Circuit4....

Terra Spider
Instructions from Terra Spider
HARDWARE:XBee Wireless Components:-SparkFun XBee Shield XBee Shield (WRL-12847) -SparkFun XBee Explorer USB (WRL-11812)-XBee 1mW Wire Antenna - Series 1 (802.15.4) (WRL-08665) (2)Moving Parts:-Power HD High-Torque Servo 1501MG From www.pololu.com -SparkFun...

Medical tricorder
Instructions from Medical tricorder
Power down your Arduino before you connect the medical tricorder shield to it. The USB type B port is really a minus development of the Arduino Mega regarding shields, because the blank USB type B port can cause short circuits or other interferences...

Robot Using Raspberry Pi & "Bridge Shield"
Instructions from Robot Using Raspberry Pi & "Bridge Shield"
We have used the bridge shield motor driver to connect to the raspberry pi instead of a separate motor driver. If you have a separate board or have made one then you can use pin numbers 4,17,22,23 from the raspberry pi GPIO header to connect to the motor...

Galileo's Finger
Instructions from Galileo's Finger
Collect all the necessary parts, tools and software dependencies:TOOLSSoldering ironHot glue gunDrill and appropriate bitsSawPencilPARTSIntel Galileo (Any micro will work – you just need serial communications and 4 output pins)2 x Stepper Motors (we...

Galileo's Finger
Instructions from Galileo's Finger
Physical build:We used a plank of pine as the basis for our prototype, for no specific reason. Use the pictures in the gallery as a guide for construction if you want to follow our layout. The gearing ratio between our driver and driven wheels are 1:2,...

ESP8266 Driving an ebay TM1638 Button/7seg display
Instructions from ESP8266 Driving an ebay TM1638 Button/7seg display
Create the TM1638 DriverInformation SourcesData sheet - TM1638elcheapo Logic analyzer from Ebay - This was a lifesaver and I could not have got this working without it!Various other examples for the Arduino code including http://www.limpkin.fr/index.php?post/2014/12/07/First-Steps-with-the-ESP8266-03-Development-BoardESP8266...

ESP8266 Driving an ebay TM1638 Button/7seg display
Instructions from ESP8266 Driving an ebay TM1638 Button/7seg display
To receive button presses via the tm1638 driver:Couple of interesting points here - Part way through I change an output to an input. I also map the odd button mapping across 4 bytes into a single byte. Teh basic sequence to read from the TM1638 isSet...

ESP8266 Driving an ebay TM1638 Button/7seg display
Instructions from ESP8266 Driving an ebay TM1638 Button/7seg display
Create the ESP8266 user_main.cThis is the main code - whose job is to connect to WIFI and setup an UDP server that listens for UDP packets and dumps them to the TM1638 display as ascii. A timer routing checks for key presses every 500 milisecs and displays...

Hydra Multi OS Gaming Console & Controller
Instructions from Hydra Multi OS Gaming Console & Controller
1) Gather the parts Start with just enough to enable & test PCI Passthrough. So you need :VTD capable system board (Mini-ITX for the Game Console version) I am currently using an Asrock H77M-ITX, which is hard to find now. The H81M-ITX/WiFi should work,...

|<
<
2
3
4
5
6
>
>|