14060 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Robot Arm
Instructions from Robot Arm
Rotary Base Construction:Here is the rotary base. I machined a disk 8" in diameter and 1" thick from nylatron. I then cut out the internal shape and atached a Gates notched belt to the internal surface with Gorilla glue. The second 8"x8" nylatron blank...

Create a Custom Dental Impression - Bondo Positive Impression
Instructions from Intraoral Respiration Monitor & Overdose Detector
The fragile alginate negative impression is used as a mold to create a tough heat resistant positive impression. The positive impression will be used to form the specialized dental thermoplastic sheets into ultra-thin ultra-clear retainers. I use Bondo...

Nautilus Windmill
Instructions from Nautilus Sculptures
List of parts to be 3D printed and the required hardware components A Handle to house the motor and batteries for actuation. This component has been reused form one my previous projects, Enchanted Thor Hammer. Refer to the list of 3D printed parts...

Collectible Card Game Counter
Instructions from Collectible Card Game Counter
The next step was to pick out a center peice. These hard drive platters all had a 1 inch hole. I went to the hardware store and picked up some small rubber feet and a pipe cap from their "small parts" bin. When I got home, using...

3D-Printed Electric Longboard
Instructions from 3D-Printed Electric Longboard
Step 2: Wheels and TrucksIn this build, I used 90 mm ABEC Flywheels with these gears from Thingiverse. (Designer: brentyi) The design I chose was the HTD5 9 mm 40 Teeth gear. They require 6 x M5 x 73 mm Socket Screws and 6 X M5 Nylock Nuts. Once you...

Two-handed chording keyboard
Instructions from Two-handed chording keyboard
Assemble materials. If possible, try the mechanical switches to suit your hands. I used the Cherry MX Clear for all buttons. Perhaps, MX Blue would be better for Alt, Control, and Shift. Anyway, for the top boards you need "Tactile", and for the bottom...

Here we show the main stages of project. The drawings of lever arms and servo bases
Instructions from Post Stroke Spasticity Rehab Helper
We use the simplest analogue servo. You can use any kind of servos. The bases, lever arms are shown in a figure: The only difficult part of mechanics component fabrication is lever arm 12. The perforation on arm must fit servo shaft perforation....

Prepare the PTFE bowden tubing
Instructions from Extruder for Prusa i3 MK3S
It is necessary to cut some kerfs, corresponding to the teeth on the extruder body. I made a 3D model for a gage to make the cutting easy. With FDM printing the hole for the tubing inside the extruder body will not be perfectly round. If you put the...

Installing Helping Hands:
Instructions from DIY Helping Hands Soldering Station
Put the cores and springs in the respective holes using glue.Take the heat shrink tubes and the alligator pins.Fix the alligator pin using super glue.After the glue dries position the heat shrink tube and shrink it.Put the heat shrink tubes on the teeth's...

Linkages/Components - Step 4
Instructions from MiniHawk VTOL
For each of the Elevon servos, repeat the same procedure as above, but with a servo arm approximately 9.5mm hole-to-center (3/8 Inch). This length can be a bit longer or shorter, the effect is increasing or decreasing elevon control throw. For servos...

Prepare X and Y motor supports
Instructions from BrailleRAP DIY Braille embosser
Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...

Amplificent
Instructions from Amplificent
Mount the Arduino TRE on the back wall of the G5 cabinet. This where the motherboard used to be, so there should be plenty of nuts attached to this wall. Obviously the attached nuts will not fit to the Arduino, so use an acrylic plate to act as a buffer...

Dress it up!
Instructions from Outside Air Temperature Display
There's plenty of gap in the enclosure where the display & switch protrude that will allow dust & dirt in. Plus, I'm not the best at hand routing so the enclosure cut was a bit ragged.I wound up printing a simple label and covering with laminate.Install...

Get a Supported Board
Instructions from TRS-80 Model 1 on a PIC32
Eitherget a UBW32 for the CPU. plenty of online retailers for this. proceed to step 2, orget an Olimex Duinomite-mini (which I use), or Duinomite with the IO adapater (which I do not have, but reportedly it also works). If you use these boards,...

FlightCPU
Instructions from FlightCPU
Once you etch and drill the holes in the board, it is time to assemble the components. Again, I apologize if I'm leaving you in the dark here (admittedly I am), but there are plenty of board assembly and soldering instructions available on the web. Of...

|<
<
1
2
3
4
5
>
>|