2230 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Connect driver boards with ribbon cables. 7-segment display boards and led board uses 10 wire cable, 14-segment displays use 12 wire cables.Note that there is no 12 wire IDC plug, so I used 14 wire plug and left the last two wires unconnected on the...

Mini Potato Cannon
Instructions from Mini Potato Cannon
7.) Poke 2 holes in the cap of the bottle about 1/4 inch apart, using another hot paperclip.

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #5, option of hard or soft enclosure): Make an enclosure out of a Hammond 1455N1602 case (Digikey part # HM980-ND). This case has plastic end panels which you can easily modify with a hot knife, file, etc. For the front panel you can print...

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #6 too, option of hard or soft enclosure): Use a 12" piece of 3" clear diameter heat shrink tubing to cover the board, the cut out the USB-mini connector with an X-acto knife, and mount rubber bumpers such as Digikey part # SJ5748-0-ND...

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
The first step to a good coffee brewing robot is to figure out how to brew good coffee. I've got some tips and tricks to brewing good coffee in the project logs ("A Dive Into the World of Coffee"), so I'll get directly into how I achieve good, full bodied...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Two 74HC595s (wired in parallel) will be driving all the LEDs in the project as well as providing power to all of the buttons. The 74HC595 is an 8 bit serial in parallel out shift register. I've written a detailed tutorial about multiplexing with the...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
The 74HC595 can only do parallel output, so I used a 74HC165 to measure the state of the buttons via 4 current limiting resistors and send this information to the Arduino. More info about the chip can be found on its datasheet.The 74HC165 has the following...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
All schematics for this project are shown above. All the Arduino pin connections are listed below:Analog0 - Gyroscope Y (Y4.5) 1 - Potentiometer 1 2 - Gyroscope X (X4.5)3 - Accelerometer Y (YAcc) 4 - Accelerometer X (XAcc) 5 - Potentiometer 2Digital0...

Guided Rocket
Instructions from Guided Rocket
Test the fitting for the outer ring to the main frame and sand if needed, it should be a solid fit. Do the same for the inner ring, it should look like the picture below. (1 ring should turn in the x axis and the other in the y)

Guided Rocket
Instructions from Guided Rocket
Using the diagram, make a power distribution board for the servosThis is roughly what it should look like

FireCoates
Instructions from FireCoates
Jacket Wiring, LED Setup, and Light Pipe Assembly.I never took pictures of this process with the first prototype so I need to complete the second prototype and take pictures to use as visual aides along the way, I should have them up in another week...

FireCoates
Instructions from FireCoates
Optional 3D Printed Jacket Module CaseDownload the Base and Top to the case and print them on your favorite RepRap OpenSource 3D Printer. It should come out looking similar to this(colors may vary ;) ):The headphone jack hole may need to be cleaned up...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Prepare the adapters and connect them to the terminal stripsThis part is important and tricky, and it took me three attempts to get this right. Here's the rules: Any high-current line must be a twin line that starts as a twin at the power supply's PCB...

|<
<
2
3
4
5
6
>
>|