Close

13748 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》레깅스룸견적よ레깅스룸ago레깅스룸メ강남레깅스룸eighty 선릉레깅스룸κ선릉레깅스⒲레깅스룸メｃ선릉레깅스룸literary"

  • Getting started
  • Instructions     from Projector Screen
  • Get and keep everything clean, including the back of your fabric. When you roll up the screen, the back touches the front, and any dirt will transfer right into the middle of your new screen. Take the actuator arm off the wiper motor. See what the threads...

  • The weight
  • Instructions     from Projector Screen
  • Keeping the screen tensioned is what keeps it flat. I provided the needed tension almost all in the vertical axis with weight. Take a scrap of your screen fabric, and test how hot you can get an iron on it, before it melts. Three layers, and two are...

  • Painting the fabric
  • Instructions     from Projector Screen
  • The light block fabric is actually three layers. White on both sides, with black plastic in between, but you are still painting fabric so you may have to experiment to get it right. Lay your light block fabric out on some hard clean surface. Don't step...

  • Joining the two
  • Instructions     from Projector Screen
  • Get help. Clean yourself. Clean the floor. Wash your hands often. Look for the weld line on the post, or otherwise establish a line along it's length. Line up your fabric with this line, and tape across the joint, applying slight tension the the fabric....

  • The supports/bearings
  • Instructions     from Projector Screen
  • Drill two holes, almost all the way through, two blocks of something the same size as the outer diameter of your roller blade bearings. It's a common size like 3/4 or 7/8in. Make them identical. For the hole you are after, you need a nut on the threaded...

  • The motor
  • Instructions     from Projector Screen
  • Take your other coupler nut, and fashion a small post coming off of it at a 90 degree angle. I welded mine. Take your corner brace, and make a second post behind the first, the thickness of the corner brace, so the main post slides on the front, and...

  • Trimming the screen
  • Instructions     from Projector Screen
  • Run the motor in the 'screen up' direction. Take a brand new, sharp razor knife and hold it against un-even ends of the rolled up fabric. Make sure the direction of travel of the material is going away from you, so the knife does't bind in the cut and...

  • The control circuit
  • Instructions     from Projector Screen
  • The relay coil is driven by 'remote power' output on the projector. There are no other connections made to the coil. As such, this also performs the needed isolation so if you screw up anything else, you at least don't fry your projector. The projector...

  • Final assembly
  • Instructions     from Projector Screen
  • Put it up on the wall and level it.  One day in the sun will remove any wrinkles, or careful application of a hair dryer will do the same.  Don't overheat it as the plastic inside can expand and ruin it.Tweak the stop positions.  Applying...

  • LED Hoodie
  • Instructions     from LED Hoodie
  • Sew the gemma onto the hoodie in a location that is relatively close to where you are putting the leds.I put it on the inside of the left half of the hoodie.Make sure you read adafruit's guide on sewing with conductive thread, especially the part about...

  • One Bad A$$ Power Inverter
  • Instructions     from One Bad A$$ Power Inverter
  • The schematics I based my inverter on I found here -http://www.eserviceinfo.com/downloadsm/61386/DROW%...I did not deviate from the design except with my choice of Mosfets , Diodes and Transformers.

  • Smile Station
  • Instructions     from Smile Station
  • On this next link is where I got the info for sending the photos taken with its own email account .http://mitchtech.net/connect-raspberry-pi-to-gmail...I tested it by copying the script to send attachments in to the python editor on the rpi by first...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday