Close

5943 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • Wiring everything together
  • Instructions     from PocketWhale
  • This is gona be a long step... Below i'm putting wiring diagram (or something that suppoused to look like on). 1. Powerbank 2. Mi band 3. Solar charging board 4. Solar panels 5. LCD screen 6. USB C for powering raspberry pi 7. Magnetic conector...

  • Raspberry Pi Glowbe Wake Lamp
  • Instructions     from Raspberry Pi Glowbe Wake Lamp
  • We’ll run the code with cron. It should start about half an hour before you get up and probably only on weekdays. Launch the cron configuration by typing the following into a terminal: crontab -e Next, set it up by adding the following line to the end:...

  • PolaPi v2.0
  • Instructions     from PolaPi v2.0
  • install fbcp (so you see the console on the GPIO Display)sudo nano /etc/rc.localdelete everything and add this text#!/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0"...

  • Norman, Coordinate
  • Instructions     from Norman, Coordinate
  • Amulet wiringNote: The wires typically used for an electronics project will not work in a costume! Typical project wires can only be bent a couple of times before breaking. They are not made to withstand the constant (even gentle) bending and flexing...

  • Test parts and fit
  • Instructions     from Better Cooling for 3D Printer Extruders
  • The heat sink had to be cut to size. Just chopped it up with a hacksaw and Dremel cutting wheel. I used a broken fan to align the holes to be drilled.It took a few tries to get the heat sink to clear everything. There was a metal bracket on the...

  • Bootstrapping
  • Instructions     from External Captions for Video Installations (extsub)
  • If everything is working, press ctrl+c to kill extsub.py, then follow these steps to run extsub at boot.   1. Make startup.sh executable: chmod 755 startup.sh   2. Open /etc/rc.local: sudo nano /etc/rc.local   and add this line so extsub...

  • From CAD to 3D
  • Instructions     from Replacement Faceplate for Pyle PLMR24 Speakers
  • Once the CAD model was created, it was a simple matter of loading the STLs into the Cura slicer and sending the data to the 3d printer. I printed everything at a 0.3mm layer height, since it didn't have to be perfect. Even at that, it looks pretty good....

  • Bolt on Modules
  • Instructions     from Autonomous Agri-robot Control System
  • The Ublox bolts onto the underside of the PCB and all the others on the top. Push them all into place and check that they work OK. The TC275 TFT screen will not work unless the EMIC2 serial1 in AND out are connected. Serial 1 is normally right next...

  • Plugging Everything In
  • Instructions     from Pentesting BBU Dropbox
  • This is the wiring part. Just follow the schematic. Plug in the Pi's USB cable for power. Plug the short patch cable into the Pi & the other end into the switch. Plug the patch cables coming from the RJ45 jacks into the switch. Plug the red wire from...

  • Gather all the parts
  • Instructions     from Smart Motor Driver for Robotics
  • The first thing you wanna do to build your own is to get all the parts. Please go to github and download the eagle files of the board. You can upload directly the design to Oshpark, if you want to use another manufacture service you will need the gerber...

  • Designing and constructing the Paludarium
  • Instructions     from Edens.Bow
  • It all started with a 55 gallon bow front aquarium. It was a used system that came with everything needed to function correctly. The filtration system was a simple over flow set up that channeled water into an under tank sump, where the water was filtered...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday