5943 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

ScottTV- A Simple MediaPlayer For My Autistic Son
Instructions from ScottTV- A Simple MediaPlayer For My Autistic Son
WoodworkingCutting a hole in the wood plate. I took the dimensions of the LCD screen and I added 1 cm on each side. Drilling 48mm holes for the buttons and test if everything fits.Fill all the irregularities with wood pasteOn the bottom 2 cut outs for...

Python L-System
Instructions from Python L-System
You will find many variables at the start of the script you can change:Rules:rules['X'] = 'X+YF+' # Dragon curverules['Y'] = '-FX-Y'axiom = 'FX'angle = 90Looking like these, you can write your own or uncomment the ones already there.iterations = 13 #...

Rocking the Horses
Instructions from Rocking the Horses
Phase 1: Step 6Simulate and run!The thing to remember about this Phase 1 is that your machine is going to cut every shape starting at 0,0. This means you need to move the machine's axis well away from the hard stops, but you can generally just bolt a...

Floating, Bamboo Makerspace
Instructions from Floating, Bamboo Makerspace
Tying Wood (Ba'at)Most of the boats are made just by tying things together REALLY TIGHTLY. They call this process "Ba'at" in Visayan.To do this just follow these steps:Get a long piece of nylon cord (or tire rubber, or string)Tie one end around some...

The Atomik Controller
Instructions from The Atomik Controller
Syncing and De-Syncing bulbsMore than one bulb can be synced to the same Device.1. Make sure power is turned off to the bulb(s) that you are going to Sync or De-Sync.2. On the Device page, after all the properties are filled in and saved, click the Sync...

Adjustable Angle Knife Grinding Jig
Instructions from Adjustable Angle Knife Grinding Jig
Then I cut out some of the 1/2" acrylic to make the base, which will also hold everything together. I made a mistake in this step and cut the plastic too small, but documented it better on the small piece, so all of the images in this step show process,...

Electric Kalimba
Instructions from Electric Kalimba
Wiring it all upI soldered wires to header pins to make all the connectors I needed. If someone wasn't able or willing to solder (aside from the teensy), you could get away with buying lots of female header pins and krimp on electrical connectors. The...

Doctor Who working Sonic Screwdriver
Instructions from Doctor Who working Sonic Screwdriver
Build notes:There are basically two ways you can build this- design the body first and then see how great a challenge it is to cram all of the electronics in there or build your electronics and then design the body around them. I sort of took the first...

Norman, Coordinate
Instructions from Norman, Coordinate
Prep and cut the amulet Step 1: Using your laser cutter software, set the outline to "cut" and the digits to "engrave".The engrave should be low power - only enough to go through the paper backing Step 2: Cut the amulet blanks, then mask off everything...

Desktop Arcade Machine : 3D Printed + RetroPie
Instructions from Desktop Arcade Machine : 3D Printed + RetroPie
Display Issue FixThe first time you try to power up the full setup, make sure to power the display from a SEPARATE USB power supply FIRST, before turning on your RPi. The display needs to be active first, otherwise your RPi would not use HDMI for display....

Atari Bluetooth Amplifier
Instructions from Atari Bluetooth Amplifier
Tools:ScrewdriverDrillDremelSoldering Iron and SolderWire Strippers\CuttersHot Glue GunMaterials:Atari FlashbackWondom AmplifierSpeaker TerminalsWire ConnectorsVolume knobShrink TubePower SupplyPanel Mounting DC Power Jack Socket ConnectorStep 1: Step...

M.A.B
Instructions from M.A.B
FIRST TEST ESP - BLYNK 1) see first instruction to install Blynk2) install ESP8266 huzzah feather board onto the arduino IDE using the following link : http://arduino.esp8266.com/stable/package_esp8266com_index.json3) Go to File > Examples > Blynk >...

Resin-in-resin
Instructions from Resin-in-resin
Drop it inOnce the epoxy has started to cure it will become like a sticky jelly on top -- not totally hard but not still a liquid. (Test with a toothpick.) At this point, it's time to add the Pi to the mold! Mix up a somewhat larger batch of epoxy. Pour...

Jukebox sound system for the hackerspace
Instructions from Jukebox sound system for the hackerspace
Set up the slack bot(if desired)this step is possibly the most painful one as you'll need to install a newer version of golang than what the debian repo supports, we solved this easily by installing golang (apt-get install golang) and then we replaced...

ARM Microcontroller Bare Chip Tutorial Series
Instructions from ARM Microcontroller Bare Chip Tutorial Series
GPIO Output Get our feet wet! Let's start Coding and Seeing Real Output Starting with the GPIO is the easiest and will get you familiar with register level code writing. Don't let the register thing scare you. Imagine you are in front of a big control...

|<
<
5
6
7
8
9
>
>|