5943 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Track mover
Instructions from Track mover
Here is the second reduction gear assembly. The motor pinion has 13 teeth and the green nylatron has 72 teeth. This reduction is ~ 5.54. Total 5.54 X 2.88 = 15.9 : 1 .

Motor Upgrade
Instructions from Quad-ROS-bot
We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...

Gearwheels assembly
Instructions from Universal Speed Reducer
Components list : 1 x Gearwheel 20 teeth1 x Gearwheel 19 teeth2 x Roller Bearing 8x22x76 x Screw M3x10 Insert the roller bearing in each gearwheel 2. Screw the six M3x10

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/mouthguard.htmlMouthguardWhat you will needSisu Mouthguard Fork Bowl Hot water MirrorTo begin assembling Pallette, you'll need to obtain the form of your top teeth. We'll use the mouthguard...

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...

Robot Arm
Instructions from Robot Arm
Rotary Base Construction:Here is the rotary base. I machined a disk 8" in diameter and 1" thick from nylatron. I then cut out the internal shape and atached a Gates notched belt to the internal surface with Gorilla glue. The second 8"x8" nylatron blank...

Create a Custom Dental Impression - Bondo Positive Impression
Instructions from Intraoral Respiration Monitor & Overdose Detector
The fragile alginate negative impression is used as a mold to create a tough heat resistant positive impression. The positive impression will be used to form the specialized dental thermoplastic sheets into ultra-thin ultra-clear retainers. I use Bondo...

Collectible Card Game Counter
Instructions from Collectible Card Game Counter
The next step was to pick out a center peice. These hard drive platters all had a 1 inch hole. I went to the hardware store and picked up some small rubber feet and a pipe cap from their "small parts" bin. When I got home, using...

Prepare the PTFE bowden tubing
Instructions from Extruder for Prusa i3 MK3S
It is necessary to cut some kerfs, corresponding to the teeth on the extruder body. I made a 3D model for a gage to make the cutting easy. With FDM printing the hole for the tubing inside the extruder body will not be perfectly round. If you put the...

Linkages/Components - Step 4
Instructions from MiniHawk VTOL
For each of the Elevon servos, repeat the same procedure as above, but with a servo arm approximately 9.5mm hole-to-center (3/8 Inch). This length can be a bit longer or shorter, the effect is increasing or decreasing elevon control throw. For servos...

Prepare X and Y motor supports
Instructions from BrailleRAP DIY Braille embosser
Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...

Attach Top to Stack Light
Instructions from Stack Light Monitor
Using a #2 phillips screw driver, remove the two mounting screws from the stack light. Fish the wire bundle through the large hole in the top enclosure piece. Use the two mounting screws to attach the top enclosure to the stack light.Trim...

Video Two
Instructions from High Powered Thermoelectric Generator (TEG)
A ten unit Thermoelectric generator system is shown being constructed and then fitted to a wood burner. The theoretical maximum output is 200 watts. The video shows how the generator was put together and how the wood burner was modified to get maximum...

▇▇▇▇ What's Next? ▇▇▇▇
Instructions from FPGA Bootcamp #0
This has been a pretty grueling bootcamp, but you should now be comfortable with basic logic gates including AND, OR, NOT NAND, NOR, and XOR. You should know about flip flops and the difference between sequential and combinatorial logic. There's plenty...

1
2
3
4
5
>
>|