Close

6194 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • END
  • Instructions     from Crius Vertical Infinity Control-Arduino USB MIDI
  • I hope you enjoyed the proccess and made one for your self! You can find everything you need for this project INCLUDING INSTRUCTIONS IN ENGLISH to my website : www.criusdigitalstudio.com You can find my projects and support me at the following social...

  • The hardware build
  • Instructions     from A 'smart' controller for a powered chair or bed
  • Putting it all together is probably the funnest part. Use your best judgement of how to arrang everything, or simply use the images as a guide. I've found that standoffs are you friend... https://www.amazon.com/gp/product/B06Y5TJXY1/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1...

  • Solder top and bottom coperr layers together
  • Instructions     from Keysheet
  • Somewhat finicky since the copper is in the middle with plastic film on the outside. Lightly tin the ends of traces but don't apply too much solder. Having a bump will make it harder to align the traces, also if you try to squash it while solder is molten...

  • Norman, Coordinate
  • Instructions     from Norman, Coordinate
  • Build the control switch Step 1: Thread a short piece of wire through the ring and the switch. Step 2: Twist the wire until the switch is solid against the ring. Step 3: Test it for fit and comfort. Step 4: Connect/solder the switch to D11-D12 on the...

  • 3D Print Some Parts
  • Instructions     from Paper Pikon with 1000mm Focal Length
  • I suggest starting by printed some parts.  You'll need most, if not all, of the parts from the original Pikon:  https://www.thingiverse.com/thing:2200862 To build this out of paper I would exclude the Tripod mount & Raspberry Pi mount. ...

  • GCODE Commands
  • Instructions     from DIY Inkjet Printer
  • The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

  • Wiring everything together
  • Instructions     from PocketWhale
  • This is gona be a long step... Below i'm putting wiring diagram (or something that suppoused to look like on). 1. Powerbank 2. Mi band 3. Solar charging board 4. Solar panels 5. LCD screen 6. USB C for powering raspberry pi 7. Magnetic conector...

  • Floating, Bamboo Makerspace
  • Instructions     from Floating, Bamboo Makerspace
  • Flooring and Post HolesLay some flat boards across the top of your floating frame. These can be from bamboo that you flatten out in thin strips, or we salvaged some marine plywood from a previous boat.It's important to leave 4 holes in your flooring...

  • Raspberry Pi Glowbe Wake Lamp
  • Instructions     from Raspberry Pi Glowbe Wake Lamp
  • We’ll run the code with cron. It should start about half an hour before you get up and probably only on weekdays. Launch the cron configuration by typing the following into a terminal: crontab -e Next, set it up by adding the following line to the end:...

  • PolaPi v2.0
  • Instructions     from PolaPi v2.0
  • install fbcp (so you see the console on the GPIO Display)sudo nano /etc/rc.localdelete everything and add this text#!/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0"...

  • Norman, Coordinate
  • Instructions     from Norman, Coordinate
  • Amulet wiringNote: The wires typically used for an electronics project will not work in a costume! Typical project wires can only be bent a couple of times before breaking. They are not made to withstand the constant (even gentle) bending and flexing...

  • Test parts and fit
  • Instructions     from Better Cooling for 3D Printer Extruders
  • The heat sink had to be cut to size. Just chopped it up with a hacksaw and Dremel cutting wheel. I used a broken fan to align the holes to be drilled.It took a few tries to get the heat sink to clear everything. There was a metal bracket on the...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday