In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...
How to flash the chip.Download the package from the download page Run "ESP_Basic_Flasher.exe"Select Your com port number and flash memory size for your chip.Hook your ESP8266 module up in flashing configuration as shown.Click the "Firmware Flash" button.Wait...
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...
VLC:Live transcoding is resource intensive, making it nice to be able to turn it on and off. Also switching the VLC configurations allows for many variations of size and quality, useful in tailor the stream to different devices and scenarios. Below are...
This is the code I used for the right frame in the first picture.#!/usr/bin/perl#use CGI qw/:standard/;use URI::Escape;my $cols = 3;my %button_codes;$button_codes{'1'}='BTN_1';$button_codes{'2'}='BTN_2';$button_codes{'3'}='BTN_3';$button_codes{'4'}='BTN_4';$button_codes{'5'}='BTN_5';$button_codes{'6'}='BTN_6';$button_codes{'7'}='BTN_7';$button_codes{'8'}='BTN_8';$button_codes{'9'}='BTN_9';$button_codes{'0'}='BTN_0';$button_codes{'Ch-'}='KEY_CHANNELDOWN';$button_codes{'Ch+'}='KEY_CHANNELUP';if...
1) Come up with a simple good idea.2) Add good ideas to it.3) Try to implement it.4) When it fails, start to strip down the design to try to get it to work.5) Strip it down more6) More...7) Rejoyce when something simple works8) Add a few simple things...
Get help. Clean yourself. Clean the floor. Wash your hands often. Look for the weld line on the post, or otherwise establish a line along it's length. Line up your fabric with this line, and tape across the joint, applying slight tension the the fabric....
On this next link is where I got the info for sending the photos taken with its own email account .http://mitchtech.net/connect-raspberry-pi-to-gmail...I tested it by copying the script to send attachments in to the python editor on the rpi by first...
Ok I pored the cement in the tube with a blue foam board on the bottom glued to the sides. That seemed to work out well accept I stuck a blue foam board cutout with a hole cut out in it to keep the 2" pvc pipe in place. Bad Idea it moved the PVC pipe...
Step 6 - Get your top graphics printed, or if you can paint the top. Your choice. If you choose to do graphics like I did, you will want to have them printed on a latex inkjet, using a quality self adhesive vinyl, with a polycarbonate...
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...
Build Payload MPDB:1) 3D printed parts needed 1x MPDB 1a1x MPDB 1b1x MPDB 21) Cut Material: Cut 1" tubing to 212mmCut 3/8" tubing to 130mmCut 3/8" tubing to 30mm2) Construct Take 30 mm section of 3/8" tubing and place it into the center hole in...
Solder wires onto the Blue, Brown, Orange, and Yellow wires, plus GND / VCC (Red and Gray). Solder to a 6 pin female header. (Or, if you have enough room inside the controller, you can use the last couple inches of cable, and just solder...