3001 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Track mover
Instructions from Track mover
Here is the second reduction gear assembly. The motor pinion has 13 teeth and the green nylatron has 72 teeth. This reduction is ~ 5.54. Total 5.54 X 2.88 = 15.9 : 1 .

Motor Upgrade
Instructions from Quad-ROS-bot
We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...

Build paper advance
Instructions from BrailleRAP DIY Braille embosser
insert the 360mm/8mm rod with a GT2 pulley 20 teeth, 3 paper roll with o-ring, and 200mm GT2 belt

Gearwheels assembly
Instructions from Universal Speed Reducer
Components list : 1 x Gearwheel 20 teeth1 x Gearwheel 19 teeth2 x Roller Bearing 8x22x76 x Screw M3x10 Insert the roller bearing in each gearwheel 2. Screw the six M3x10

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...

Assembling right side
Instructions from BrailleRAP DIY Braille embosser
Fix 3d printed parts BOTTOM_AXIS_right and TOP_AXIS_right on the frame with M3 washers M3 Nyl nuts and M3-14 Fix 3D printed parts KP08_support and KP08 on the frame with M5 washers M5 Nyl nuts and M5-25 screw Fix a KFL08 with M5 washers...

Robot Arm
Instructions from Robot Arm
Rotary Base Construction:Here is the rotary base. I machined a disk 8" in diameter and 1" thick from nylatron. I then cut out the internal shape and atached a Gates notched belt to the internal surface with Gorilla glue. The second 8"x8" nylatron blank...

Create a Custom Dental Impression - Bondo Positive Impression
Instructions from Intraoral Respiration Monitor & Overdose Detector
The fragile alginate negative impression is used as a mold to create a tough heat resistant positive impression. The positive impression will be used to form the specialized dental thermoplastic sheets into ultra-thin ultra-clear retainers. I use Bondo...

Nautilus Windmill
Instructions from Nautilus Sculptures
List of parts to be 3D printed and the required hardware components A Handle to house the motor and batteries for actuation. This component has been reused form one my previous projects, Enchanted Thor Hammer. Refer to the list of 3D printed parts...

3D-Printed Electric Longboard
Instructions from 3D-Printed Electric Longboard
Step 2: Wheels and TrucksIn this build, I used 90 mm ABEC Flywheels with these gears from Thingiverse. (Designer: brentyi) The design I chose was the HTD5 9 mm 40 Teeth gear. They require 6 x M5 x 73 mm Socket Screws and 6 X M5 Nylock Nuts. Once you...

Here we show the main stages of project. The drawings of lever arms and servo bases
Instructions from Post Stroke Spasticity Rehab Helper
We use the simplest analogue servo. You can use any kind of servos. The bases, lever arms are shown in a figure: The only difficult part of mechanics component fabrication is lever arm 12. The perforation on arm must fit servo shaft perforation....

Linkages/Components - Step 4
Instructions from MiniHawk VTOL
For each of the Elevon servos, repeat the same procedure as above, but with a servo arm approximately 9.5mm hole-to-center (3/8 Inch). This length can be a bit longer or shorter, the effect is increasing or decreasing elevon control throw. For servos...

Prepare X and Y motor supports
Instructions from BrailleRAP DIY Braille embosser
Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...

Video Two
Instructions from High Powered Thermoelectric Generator (TEG)
A ten unit Thermoelectric generator system is shown being constructed and then fitted to a wood burner. The theoretical maximum output is 200 watts. The video shows how the generator was put together and how the wood burner was modified to get maximum...

1
2
3
4
5
>
>|