3147 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

650nm 5mw Laser Build
Instructions from 650nm 5mw Laser Build
After some scrounging around I found a cheap axis laser housing with diode and driver board still intact! For me, this is a mirracle as most of the time, I usually disassemble things when I first get them.After I scrounged up the rest of the parts I...

The HYDRA multiheaded virtual computer
Instructions from The HYDRA multiheaded virtual computer
Gather parts to build a system for your intended purpose:Research your system board & processor & be double or more sure it is supported. Number of PCIe, PCI should reflect what you want to run. Internal serial HEADER is preferable over DB9 on...

The HYDRA multiheaded virtual computer
Instructions from The HYDRA multiheaded virtual computer
At this point you have an assembled system, VT-d capable CPU & Board, 8+ GB RAM, 2+ ATI GPU's of at least HD5xxx, bootable storage for ESXi and storage for VM's, can boot the ESXi installer from cd/usb/iso, and a supported nic. Get ESXi installation...

Pressure Cooker Vacuum Chamber
Instructions from Pressure Cooker Vacuum Chamber
Step 5: Final assembly Now is the time for that pressure cooker lid that you set aside earlier.The gasket that's in the lid of the Miro pressure cooker is very easy to remove. Just give it a gentle tug and work your way around the lid. It should come...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Two 74HC595s (wired in parallel) will be driving all the LEDs in the project as well as providing power to all of the buttons. The 74HC595 is an 8 bit serial in parallel out shift register. I've written a detailed tutorial about multiplexing with the...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
The 74HC595 can only do parallel output, so I used a 74HC165 to measure the state of the buttons via 4 current limiting resistors and send this information to the Arduino. More info about the chip can be found on its datasheet.The 74HC165 has the following...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
This instrument is primarily a MIDI device, so we need to build a MIDI out. There are two ways to do this (and over the course of this project I did one and then switched to the other):output MIDI via a 5 pin DIN connector output MIDI via USB (this is...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
All schematics for this project are shown above. All the Arduino pin connections are listed below:Analog0 - Gyroscope Y (Y4.5) 1 - Potentiometer 1 2 - Gyroscope X (X4.5)3 - Accelerometer Y (YAcc) 4 - Accelerometer X (XAcc) 5 - Potentiometer 2Digital0...

HPDL watch
Instructions from HPDL watch
Let's start with PCB. I wanted to mound display on one side of the PCB and the uc - on the other. Unfortunatelly, uc barely fits in the middle of the display's back and some pinout traces of display and uc touches where they mustn't. The traces...

HPDL watch
Instructions from HPDL watch
The code is next. It's available at my github, I'll just explain a little bit. The timer2 is set to overflow and it's prescaled to 1024. With 32768 Hz clock it overflows every 8 seconds. Then I add 8 secs to the time variable. I've also set INT0...

Seeing the invisible
Instructions from Seeing the invisible
5) Lights Camera Action.... Turn on the light source. Make sure the beam is parallel. Place aperture at the focal point of the second lens. Place camera inline with the whole system. When fully zoomed out the camera should see a bright point where the...

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Getting the parts.So the cat 5 cabel wasnt that hard to get you can get it from any store that sell electronic or you can get it from ebay.I got my from a store for only 30 cent a meter.And the usb over cat 5 you can get from ebay or a electronic store...

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Putting it all together.This is fairly easy beacuz you just have to conect some wires and do some solderin job for the cat 5 cable and nothing else

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Drill front and base, mount front on base plateStraight forward: My banana jacks needed 8 mm holes, the cable glands needed 12 mm-ish (12.5? I'm not sure what I used), then there's 5 mm for the switch and 3.2 mm for the LEDs, and finally 8.5 mm for the...

|<
<
2
3
4
5
6
>
>|