3734 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Experiment Bioroid!
Instructions from Experiment Bioroid!
Repeat 5 and 6 step for all servos.

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Program the Digispark and temporarily connect the servo to test the software and servo. I had a batch of 5 identical servos. Two of them rotated contuously when the Digispark was reset. The other three worked fine. One of those three was very jittery....

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Temporarily put a jumper between ground and the input pin on the header under the box. Turn on the system. After a 5 second delay the servo should move to zero then full scale then back to zero. You may have to adjust the mounting of the pointer...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Now the meter is ready to display any dc voltage between 0 and 5 volts connected between the gound and Vin1 pins on the box header.

Portable LED Floodlight
Instructions from Portable LED Floodlight
Build a tripod. You may have to re-stock materials at this point. Might I suggest a stout? Always goes with metal work.I started with a halogen work lamp which was at the end of the line.. yanked the 15" legs off and replaced them with 4ft pieces...

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #5, option of hard or soft enclosure): Make an enclosure out of a Hammond 1455N1602 case (Digikey part # HM980-ND). This case has plastic end panels which you can easily modify with a hot knife, file, etc. For the front panel you can print...

Story Sphere
Instructions from Story Sphere
http://www.instructables.com/id/Hemisphere-Keyboard/

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
The first step to a good coffee brewing robot is to figure out how to brew good coffee. I've got some tips and tricks to brewing good coffee in the project logs ("A Dive Into the World of Coffee"), so I'll get directly into how I achieve good, full bodied...

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
Effective Bardware Based Stepper Motor ControlIn my quest to derive a robot control scheme from scratch, I've been working to figure out how to control a stepper motor. Stepper motors are great because they're cheap, relatively simple to control,...

Making a BR-900CD Stand on its own
Instructions from Making a BR-900CD Stand on its own
After reminiscing about my audio recording gear, I started thinking about a stand that I had purchased with the express idea of mounting the BR-900CD onto. It was a heavy duty music stand that I had picked up on sale for 20 dollars. After I got it home,...

Atari 5200 Custom Controller Build
Instructions from Atari 5200 Custom Controller Build
The problem lies in the lack of response, over time the little pads inside become corroded and unresponsive. Eventually, no amount of cleaning and disassembling actually fixes this and you end up replacing either the entire controller or purchasing one...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
PVC Cooling Jacket for CO2 Laser0PVC Cooling Jacket for CO2 LaserThe adventure begins while I was walking around the local home depot looking at ideas on how to build the laser. I was sort of making it up as I went. Mapping things out in my mind. I wanted...

650nm 5mw Laser Build
Instructions from 650nm 5mw Laser Build
After some scrounging around I found a cheap axis laser housing with diode and driver board still intact! For me, this is a mirracle as most of the time, I usually disassemble things when I first get them.After I scrounged up the rest of the parts I...

|<
<
5
6
7
8
9
>
>|