3734 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Seeing the invisible
Instructions from Seeing the invisible
5) Lights Camera Action.... Turn on the light source. Make sure the beam is parallel. Place aperture at the focal point of the second lens. Place camera inline with the whole system. When fully zoomed out the camera should see a bright point where the...

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Getting the parts.So the cat 5 cabel wasnt that hard to get you can get it from any store that sell electronic or you can get it from ebay.I got my from a store for only 30 cent a meter.And the usb over cat 5 you can get from ebay or a electronic store...

Hack a webcam and turnit into a security camera
Instructions from Hack a webcam and turnit into a security camera
Putting it all together.This is fairly easy beacuz you just have to conect some wires and do some solderin job for the cat 5 cable and nothing else

Guided Rocket
Instructions from Guided Rocket
Drill 3mm holes in the necessary spotsScrews ready for mountingOuter ring will be attached to this pivot

Guided Rocket
Instructions from Guided Rocket
Buy and place metal gear servos in the main frame and epoxy the tabs. Next attach 1 rod to each ring, and to each servo so that the rotation of the servo changes the angle of the ring

Guided Rocket
Instructions from Guided Rocket
Using the diagram, make a power distribution board for the servosThis is roughly what it should look like

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Drill front and base, mount front on base plateStraight forward: My banana jacks needed 8 mm holes, the cable glands needed 12 mm-ish (12.5? I'm not sure what I used), then there's 5 mm for the switch and 3.2 mm for the LEDs, and finally 8.5 mm for the...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Prepare the adapters and connect them to the terminal stripsThis part is important and tricky, and it took me three attempts to get this right. Here's the rules: Any high-current line must be a twin line that starts as a twin at the power supply's PCB...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Drill front and base, mount front on base plateStraight forward: My banana jacks needed 8 mm holes, the cable glands needed 12 mm-ish (12.5? I'm not sure what I used), then there's 5 mm for the switch and 3.2 mm for the LEDs, and finally 8.5 mm for the...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Build and mount the minimum load boardThe minimum load board is a piece of stripboard that carries 5 screw terminals and the load resistors:Mounted with 4 screws and 20 mm spacers, and connected to the power supply. Note that I accidentally used the...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
TestMake sure that both the switch in the front plate and the power supply switch are off. Attach a cable to the power supply and switch it on. The standby LED should be on, indicating that 5Vsb is available. 5 Vsb should really be 5 V. The other outputs...

Ultrasonic Parking Aid without Arduino
Instructions from Ultrasonic Parking Aid without Arduino
If you want to burn sketches using ICSP, you can use this boards.txt descriptor, taken mainly from the Arduino Pro Mini:atmega328t.name=ATMega 328 (8 MHz) - USBTinyISP atmega328t.upload.using=arduino:usbtinyisp atmega328t.upload.maximum_size=32768 atmega328t.upload.speed=57600...

Ultrasonic Parking Aid without Arduino
Instructions from Ultrasonic Parking Aid without Arduino
It is useful to have a serial port for debugging sketches. If you want a serial port, populate the serial header along with the 10K pullup resistor and auto-reset capacitor. You might as well run a bootloader if you have a serial port: use this descriptor...

Ultrasonic Parking Aid without Arduino
Instructions from Ultrasonic Parking Aid without Arduino
If you have a 3D printer, there are STL and DesignSpark Mechanical files for an enclosure. The stand off is sized to self tap with a #4 3/8" screw.

Arduino Pi: an Arduino computer for developers.
Instructions from Arduino Pi: an Arduino computer for developers.
The anode rows should connect to digital pins 0-4 and the cathode columns should connect to digital pins 5-9. Based on the diagram in the previous steps, connect AN0 - AN4 to pins 0-4 and CA0- CA4 pins 5-9.

|<
<
7
8
9
10
11
>
>|