71 Results for "Q%20%ED%85%8D%EC%82%AC%EC%8A%A4%ED%99%80%EB%8D%A49%20cddc7_com%20%E2%98%8F%ED%94%84%EB%A1%9C%EB%AA%A8%EC%85%98%EC%BD%94%EB%93%9C%20B77%E2%98%8F%EC%98%81%EB%8D%95%201xbet%E2%85%95%EB%B6%81%EC%A4%91%EB%AF%B8%EA%B3%A8%EB%93%9C%EC%BB%B5%E0%AC%B9%EC%95%84%EC%8B%9C%EC%95%84%EC%B6%95%EA%B5%AC%E1%BB%86%EB%B9%85%EC%B9%B4%EC%A7%80%EB%85%B82%C6%9B%ED%85%8D%EC%82%AC%EC%8A%A4%ED%99%80%EB%8D%A49%EB%A6%AC%EB%B7%B0%20indianocean/"
First, let's assemble the extruder, so we can just drop it onto the printer later! There are two sets of spacers, labeled B1-B7 for the Bottom assembly, and T1-T2 for the top assembly. There is also an extruder motor shaft coupler spacer, labeled...
The components are attached to a baseplate (95(W) x 128(L) mm), which is fitted to the back of the MDE's with M3 X 25mm bolts and 10mm standoffs. Four bolts are fitted through the holes in the Neopixel support board and the standoffs fitted to attach...
1. Make the cable guide. Cut a 6-flute section out the 36" 10mm Corex sheet, and then make scores (not cuts) at 1" intervals, starting at one side, and moving inward 18". Use a razor blade and straight edge to make scores perpendicular to the flutes...
It helps to have the wooden arc clamped sideways to a table for this part. Insert the LED wires into the top of the case and the wooden arc in too. Add the clamp piece to the back of the case and bolt together with the M4 bolts and nuts (inserted...
Using some spare red and black wire cut from either the J1772 cables or the AC cable, make four jumpers to carry the two AC hot lines from the power distribution module to each of the two contactors. Crimp ferrules onto each end of each jumper. Pass...
You should find all the major components in the "Components" tab of this project. Additionally, all of the models in the OnShape document linked on the project homepage should be printed, and the custom PCB provided in the project documents should be...
Detach AC wires, pry open the device with a screwdriver/club card/, find the screw terminal blocks. In V2 the switch terminals are gray, in V1 black, find the ones marked S_IN and S_OUT = the ones with no thick solder snakes coming from them. Those...
howto make a generator1. 3V Dc motor – inside toys which using two batteries 1.5 V AA 2. coil without core inside syncronous motor 230 V – A4 laminators, microwave turntable motor - remove the core inside the motor 3. neodymium magnet sphere 13 mm 4....
The construction work of the CNC machine is pressing go on your CNC machine. But as anyone knows, CNC work is 95% setup and 5% cutting! A few words on setup are important here. First, getting a solid fixture is essential. I am choosing to hold down the...
This was the previous Hotplate project, which expanded the heating area by connecting the cloth iron's element to a copper plate. A mechanical mechanism called a thermostat was used to control the heating element of the original version of the hotplate....
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...
This is the trickiest part because the high voltage high current EV coaxial cable is not available to consumers. And the HV connectors are nearly as difficult to get and figure out what parts you need. I used a 4 conductor cable to keep a ground wire...