6761 Results for "《 예약문의 OIO↗8489↗8306》청담가라오케П㈄delightfulセ가라오케가라오케νreflected 가라오케사이즈가라오케 가라오케추천㎙가라오케ｑbring㈀"

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Mini Potato Cannon
Instructions from Mini Potato Cannon
3.) Push the hot paperclip through the pen tube about 1/4 inch from the end.

Mini Potato Cannon
Instructions from Mini Potato Cannon
4.) Shove the paperclip end of the tube into the hole in the bottle, until the paperclip is touching the bottle (but not inside it).

Mini Potato Cannon
Instructions from Mini Potato Cannon
7.) Poke 2 holes in the cap of the bottle about 1/4 inch apart, using another hot paperclip.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
3.) Slide the coiled paperclip off of the screwdriver or rod.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
4.) Snip off each ring from the coil.

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Power to Servo motor So, we've written the code. Now start all wiring stuff:We have two options:Give 5V to servo motor from Arduino.Here, you can connect the servo motor ( attach a small fan to the motor ) to Arduino Uno. Servo motor has 3 wires: Connect...

Animatronic Iron Man MKIII suit
Instructions from Animatronic Iron Man MKIII suit
Notes about tools and materials used:ProPoxy 20 is awesome stuff. When making the brass tube pivots for the shoulder rocket pods it was easiest to glue the brass tube to the servo casing with superglue ( I use Gorilla glue with a spray accelerator) and...

Late Night Reading Lamp
Instructions from Late Night Reading Lamp
Solder LEDs, resistors etc onto a bit of veroboard. I used a female PCB header for plugging in the battery so that I didn't have to route long cables around the frame. Leave some length on the LED pins so that they stand up a bit from the veroboard

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Wire up the circuit. Use 3-pin and 6-pin male headers to connect to the Digispark rather than wiring directly. This will allow easy disconnection of the Digispark for reprogramming. Optionally use a 3-pin header for connection to the servo in case...

Portable LED Floodlight
Instructions from Portable LED Floodlight
Spend some time on your LED and battery selection. These are the two most expensive items, and of course the most important.In my case I'm trying to light a volleyball court. The light I'm considering is available in 30º spread or 60º spread....

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Add the ZTEX LX25 FPGA Module, which with the OpenADC, should now look like this, using a 0.375" hex stand-off with 4-40 screws for the OpenADC:

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #5, option of hard or soft enclosure): Make an enclosure out of a Hammond 1455N1602 case (Digikey part # HM980-ND). This case has plastic end panels which you can easily modify with a hot knife, file, etc. For the front panel you can print...

|<
<
3
4
5
6
7
>
>|