Close

6761 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た 《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸₩셔츠룸ⓤsilverⓞ"

  • Motor Upgrade

  • We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...
  • Nautilus Twins

  • List of parts to be 3D printed and the required hardware components A 90 teeth spur gear. This would mate directly with the Nautilus gear.A compound gear with 30 teeth to mate with the 90 teeth gear to get the factor of 3 reduction in speed.A second...
  • Mechanicals

  • In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...
  • Pallette

  • http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...
  • Solarmodule preparation

  • Carefully put solar module on some soft underground so the front does not scratch. Then cut the long wire to around 50cm (see backside image as reference). Everything will be put in the back of the panel and there is plenty of room.
  • "Programming" sockets

  • The sockets used to hold the 3 "programming" components R1, R2 and C are machined header pins stripped of their supporting plastic. An example of these can be seen here at Sparkfun, but these are available from plenty of other places too.
  • Nautilus Windmill

  • List of parts to be 3D printed and the required hardware components A Handle to house the motor and batteries for actuation. This component has been reused form one my previous projects, Enchanted Thor Hammer. Refer to the list of 3D printed parts...
  • 3D-Printed Electric Longboard

  • Step 2: Wheels and TrucksIn this build, I used 90 mm ABEC Flywheels with these gears from Thingiverse. (Designer: brentyi) The design I chose was the HTD5 9 mm 40 Teeth gear. They require 6 x M5 x 73 mm Socket Screws and 6 X M5 Nylock Nuts. Once you...
  • Two-handed chording keyboard

  • Assemble materials. If possible, try the mechanical switches to suit your hands. I used the Cherry MX Clear for all buttons. Perhaps, MX Blue would be better for Alt, Control, and Shift. Anyway, for the top boards you need "Tactile", and for the bottom...
  • Linkages/Components - Step 4

  • For each of the Elevon servos, repeat the same procedure as above, but with a servo arm approximately 9.5mm hole-to-center (3/8 Inch). This length can be a bit longer or shorter, the effect is increasing or decreasing elevon control throw. For servos...
  • Nautilus Triad

  • List of parts to be 3D printed and the required hardware components 3 Gear frame3 Nautilus gearsPegs to attach the gears to the frame608 BearingsActuator Assembly Instructions Mount the gears on the frame. Ensure that the teeth are meshed as shown...
  • Nautilus Quad

  • List of parts to be 3D printed and the required hardware components 4 Gear frame4 Nautilus gearsPegs to attach the gears to the frame608 BearingsActuator Assembly Instructions Mount the gears on the frame. Ensure that the teeth are meshed as shown...
  • Nautilus Butterfly

  • List of parts to be 3D printed and the required hardware components 4 Links4 Nautilus gearsPegs to attach the gears to the frame608 BearingsActuator Assembly Instructions Connect the links to create the frame.Mount the gears on the frame. Ensure...
  • Prepare X and Y motor supports

  • Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...