Close

2277 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • Ribbons and Wires
  • Instructions     from CRTelecaster
  • Now for the actual control of the tones. You will need the soft potentiometers (https://www.sparkfun.com/products/8679), guitar/ukulele neck, 10k ohm resistors, and wires for this step. I used 2 because my neck was too small to fit more. I would try...

  • Modelisation
  • Instructions     from The Piranha Plant
  • 1st step : To begin our project the look of it is really important that's why we had to modelize our pirhana plant 2nd step : We have to design 3 parts : - the head (we choose to do it in translucid PLA to be sure that the light will go through it) -...

  • Pressure Cooker Vacuum Chamber
  • Instructions     from Pressure Cooker Vacuum Chamber
  • Step 6: Vacuum time Well, we're finally here. It's time to turn on the vacuum pump, and run for cover. Maybe.Before we actually flip the switch, a few words of caution from our sponsor.First, be sure to read the instructions that came with your pump....

  • Serial-over-IP Application
  • Instructions     from Serial-over-IP Application
  • Configuring the VSP-DS1101 linkConnection WizardLaunch Connection Wizard (it is a part of the TDST).On the first screen, select "Create a link between a Virtual Serial Port and a Device Server". Click Next.Select the number of the VSP (virtual COM) you...

  • Terminal blocks
  • Instructions     from Over-engineered LED strip controller
  • The board will have a total of 28 screw terminals for attaching various wires. It's 2 blocks of 6 pins and 4 blocks of 4 pins. They are arranged around both the top and bottom of the PCB. How you place the terminal blocks will depend in part on your...

  • It All Comes Together
  • Instructions     from Binary Wrist Watch
  • By now we have gathered all the parts now it's time to put everything together. Due to a lot of planning this step is really easy and straight forward. Take a look at the pictures to see the order of how everything is mounted. The screws used to mount...

  • Step 1: verify that everything works properly
  • Instructions     from Modular 5-bar robot
  • NOTE: none of the following steps require a power supply connected to any of the boards, but in case you want to do so, connect the power supply to the board BEFORE plugging it to your PC and opening the port, as this may cause a short circuit on your...

  • Print parts
  • Instructions     from Zvychai One
  • No step-by-step instructions here, follow your printing intuition/experience, but few tips would be: I'd say print everything except small covers with 3-4 walls and 30-40% infill. Most parts do not require much printing support except maybe if you have...

  • Cylinder
  • Instructions     from Printing bones on a DIY powder bed 3d printer
  • Preface If you are lost or don't understand the guide completely take a look at the A360 site. Cylinder To assemble the cylinder you will first have to assemble the pistons. You will need 2 or 4 M6 threaded rods per piston. You will also need one nut...

  • Power Gear Assembly
  • Instructions     from 3D Printed Pendulum Clock
  • This section shows the process of assembling the gears into the frame.  There are a few preparation steps that need to be completed before assembly.  For now I will just leave it as "print everything and cut the axles to length".  More...

  • Laser Layer Assembly (Layers 3-9)
  • Instructions     from Upright Laser Harp
  • These layers hold together the laser, photoresistor walls, and mirror assemblies. All the layers are the same except for layer 3, which has additional holes for mounting the top assembly. For each row, the laser/photoresistor and mirror positions alternate,...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday