314 Results for "%EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1%2B%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F %EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8%E2%89%AE%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC%E2%88%80 %EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5 %E2%88%91%EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5%C2%B1 %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1%E2%88%86 %EA%B0%95%EB%82%A8%EB%A3%B8%E2%88%82 %EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E2%89%AE %EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC%E2%88%8F east"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

[2016] InternetS of Energy - Call me DAISEE
Instructions from [2016] InternetS of Energy - Call me DAISEE
Ethereum installation on a Raspberry PIAn Ethereum node running on a Raspberry Pi. Photo by RIeul (CC-BY-NC-SA) Equipment 3 Raspberry Pi with Ethereum client (each Pi = a node of a blockchain) 3 SD cards 2 computers Other solution Using Wio Link to simulate...

Trying out GATTTOOL
Instructions from Reading a bunch of BLE sensors with raspberryZero
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Provisioning the Raspberry Pi
Instructions from GePS
Next, you're going to get the SD card ready for booting the operating system on the Raspberry Pi. This begins with copying the official raspbian lite image to the SD card. This is a process that can be done in many ways, and it slightly differs depending...

DIY Data Logger
Instructions from DIY Data Logger
Here's the code for the Spark Core. The programming for this is very similar to an Arduino. Once you go to the Spark website and get your Core setup you just click on the BUILD tab, create a new App and paste in the code and it'll upload the code over...

Prep Your Board!
Instructions from Sotto: A Silent One-Handed Modular Keyset
Cut your protoboard to roughly fit the size of the Feather. Use your wires to take the inconveniently placed pins and turn them into tidy little rows of four. The rows should be: A0 3v Gnd 11 A1 3v ...

I2C Sensors and debugging
Instructions from Stratux ADSB Receiver and AHRS
I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...

Run a Program
Instructions from Analog Speedometer Using Arduino and IR Sensor
#includeLiquidCrystal lcd(A5,A4,A3,A2,A1,A0);#include const int stepsPerRevolution = 200; // change this to fit the number of steps per revolutionStepper myStepper(stepsPerRevolution, 8, 9, 10, 11);volatile byte REV; unsigned long int rpm,RPM;unsigned...

Fan controller for Re:Load Pro
Instructions from Fan controller for Re:Load Pro
Make you the PCB and get the components and any standard 60mm 4-wire fan will probably do the job. I used a JMC "6015-12HB APW" that I had lying around. The exact the same fan is readily available on eBay.I used eagle to design my PCB, and the files...

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
Arduino Mega Code The code in the main control panel is fairly standard except for the part which sends data down the I2C bus to the Adafruit Feather slave. This code can be found in 'void sendData()' below and involves disassembling complex float numbers...

EDID Inserter
Instructions from EDID Inserter
Plug in the freshly minted EDID Inserter and a repeated invocation of the following should yield only 256 FFs typical of an EEPROM fresh from the factory:sudo i2cdump 3 0x50Dire admonitions are issued even when merely trying to read:No size specified...

Run a Program
Instructions from IoT Digital Thermometer using LM35 and NodeMCU
#include const char* ssid = "*********"; // Your ssid const char* password = "***********"; // Your Password float temp_celsius = 0; float temp_fahrenheit = 0; WiFiServer server(80); void setup() { Serial.begin(115200); pinMode(A0, INPUT); Serial.println();...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

1
2
3
4
5
>
>|