13548 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Step 8: Installing Personal Weather Station
Instructions from IoT Personal NodeMCU ESP12 WiFi Weather Station
The location weather station is the most important part of installation. If weather station is located under a tree or an overhang, the rainfall data measured by the station will not be correct. If you place your weather station in an alley, you could...

Customer interviews
Instructions from A desk for an engineer
If its a new product that has never been seen before or a copy of an old product, a customer will eventually use the thing. Even if it is just for your personal use, write down your needs so you can hit all your goals. For this project I wrote down what...

Step 2: Photo Editing
Instructions from Coin Card
I'm using GIMP, just because I have used it a few times. It is easy enough to get used to, especially when you can google just about anything you want to do on it. First, I need to decide which colours can be merged into one. I have 4 colours to work...

Assemble the motor mount and first stage
Instructions from Astrophotography Camera Mount
Set the motor mount retainer on top of the stepper motor and attach with 4 x M3 screws. Press-fit the 5 : 1 sun gear with the motor shaft axle to the stepper motor shaft. (note: the motor mount STL doesn't have the four holes in the plate right...

Key dublication
Instructions from A simple casting mould for hot metal key copying
Step 1: Fill the cavity of the mould with Fimo or a equivalent polymer clay and flatten the clay e.g with a round pice of wood or core follower. To prevent the two clay parts from sticking together while making the key indentation, powder some talkum...

Step 2 Soldering the circuit
Instructions from Music Accessibility
1. prepare all the material : An arduino sheildSoldering materials4 servo motors4 buttons120cm wires * 12 60cm wires * 8 2. Braid the wires This step is for better wiring management and for avoiding short circuits. Braid the 60cm wires...

Motor drive
Instructions from Eazy Peasy High Voltage Variable Capacitor
The basic capacitor is done. This next section is how I built a motor drive to remotely position the capacitor. I decided to use a DC motor. Perhaps a stepper is a better idea, but for now I like this design. The motor I chose is overkill. It was...

Electric Kalimba
Instructions from Electric Kalimba
Wiring it all upI soldered wires to header pins to make all the connectors I needed. If someone wasn't able or willing to solder (aside from the teensy), you could get away with buying lots of female header pins and krimp on electrical connectors. The...

Manual SMT Pick and Place Machine
Instructions from Manual SMT Pick and Place Machine
Since we're going to actually hack a pre-existing product - a shop bought CNC engraving machine - the first step is to assemble the CNC engraving/laser machine - it comes as a kit with instructions of it's own (see below). The upright aluminium 2020...

Acrylic Tiles and Stand Assembly
Instructions from EnLIGHTen Web-Connected, OPEN source, LED Clock
After you apply the finish to the wood pieces, it's time to press in the acrylic tiles and assemble the stand. The acrylic tiles are press fit tolerances and don't require any adhesive generally speaking. A few of the tiles may need small amounts...

Mains Power Wiring
Instructions from Pentesting BBU Dropbox
Next, we're going to start extending wires and mapping out where we want things to go. I like to add plenty of wire ahead of time and trim to fit as I go. Extend the wires coming from the power cord and solder the white and green to the proper sides...

Hot Air Exhaust
Instructions from Nibbler Table Saw
The simplest of changes was to add a hot air exhaust port and duct. I chose Chardonnay because its oaky tones complemented the oak in the top. You can choose a nice red, just NOT MERLOT! This may look large, but I wanted to make plenty of room...

Upload firmware into the system
Instructions from Programmable Light Controller
Once all the components are assembled the next task is to feed firmware into the microcontroller. To upload the firmware the most recommended method is to use AVR in-circuit programming (ISP) compliant adapter. This system is designed to work with standard...

Soldering
Instructions from Knobo
Use the schematic on my Github as a reference when soldering. I chose to hand solder the PCB since I don't have the equipment for hot air soldering. If you also choose to solder the PCB by hand, be sure to use plenty of flux, a good pair of...

Testing the Cans
Instructions from The Wireless Tin Can Telephone
To test it out, you’ll need to turn both cans on. Press the button down on one can, and make some noise into the microphone. Can you hear audio coming from the other can? Try the same thing on the other can. Hear anything? If so, it works and...

|<
<
3
4
5
6
7
>
>|