870 Results for "%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%9C%9Awww%2Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%20%EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%9C%9A%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%9B%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%9B%20%EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94%20%EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84"

Software Setup
Instructions from MQTT NOAH Baseboard
Intro: The most important part to get any electronics project you download from the internet up and running is the software tool chain. If you don't manage to get this set up it causes hours of frustration long before you get to the interesting part. ...

NEO8M configuration with u-center
Instructions from GNSS bluetooth module with u-blox NEO8N
To configure the u-blox NEO8N module you can hook it up via serial or USB. Here I connected it with the USB port and the device registred as COM5 on my PC. In Linux you may have to check the com port since wine generates all com ports new on startup....

Testing Completing the Transmitter Receiver Pair
Instructions from DIY Radio Controller for Drone | nRF24L01
So as we are done with the Complete Setup of the Transmitter and the Hardware Setup of our Drone Receiver. Now we need to test the pair so for that we will follow the steps given below:- Head over to the Github repository of the project from here. In...

Super low cost VGA output for the Pi Zero
Instructions from Super low cost VGA output for the Pi Zero
SALVAGING CONNECTORSIf you have an old VGA cable (check with your local IT department, they probably have boxes of them) you can salvage the connectors. Start by pulling out the thumbscrews with pliers. Then use a hack saw to cut the ends off, but instead...

Pre Processing Original Image
Instructions from Automatic Reading Machine
Once the image is captured, the system applies a sequence of computer vision algorithms in order to improve the quality of the picture. The main objective here is to make the text in the image as evident and recognizable as possible, which is essential...

With the case and and device pieced together, we now need to connect with Arduino IDE
Instructions from Build a People Counter for $30 Using NodeMCU
To start, connect your NodeMCU to your computers port using the micro USB Note: If you do not already have the Arduino IDE, click here to download. 1.- Open the Arduino IDE, select Files -> Preferences. >Next input the following URL into the Additional...

PolaPi v2.0
Instructions from PolaPi v2.0
Rasbian Jessie Lite Pls download the latest version of Jessie Lite https://www.raspberrypi.org/downloads/raspbian/ write it to an SD Card (16GB recommended but 8GB would work too) boot your Pi, attach ethernet cable (or configure wifi) and enter the...

thingSoC NEOLED Driver
Instructions from thingSoC NEOLED Driver
TSOC_NEOLED Arduino Sketch ExamplesUnder the "examples" directory are several Arduino IDE examples for using the TSOC_NEOLED board with Arduino IDE. Using the Arduino "Wire" library for I2C communications, it is simple to control the TSOC_NEOLED // Start...

CortanaRoom home automation
Instructions from CortanaRoom home automation
Step 4: Make the hardwareShow All ItemsNow we have the software part done we need to go to the hardware part.For the hardware we need 1 arduino uno or nano a lot of long wires! 3 mosfets i use the IRFZ44N 4 5V ( 12V is possible with extra circuitry)...

Uploading the Arduino bootloader to the STM32
Instructions from Using a STM32 like an Arduino Tutorial | STM32F103
1) Connect the STM32F103 with an FTDI board as in the picture. 2) Switch the BOOT 0 header from the '0' position to the '1' position before connecting the FTDI board to the computer for flashing the bootloader 3) Download the appropriate bootloader(PC13...

ESP32 Camera Build
Instructions from ESP32 Touchscreen | DIY Digital Camera | Gaming
Here we will use the ESP32 Touch Cam module from Makerfabs to build a DIY Digital Camera. For that, we do not need to do any extra connections. we just need to connect the module to our PC, and uploading the code will make it ready to use. For building...

Screenshot Receiver using ESP32 Touch Cam module
Instructions from ESP32 Touchscreen | DIY Digital Camera | Gaming
In the last step, we built a digital camera using the Touch Cam module now in this step we will try another interesting application of the ESP32 Touch Cam module which is the Screenshot Receiver. What a Screenshot Receiver does is that it captures data...

Step 1: verify that everything works properly
Instructions from Modular 5-bar robot
NOTE: none of the following steps require a power supply connected to any of the boards, but in case you want to do so, connect the power supply to the board BEFORE plugging it to your PC and opening the port, as this may cause a short circuit on your...

How to use Oasis controller software
Instructions from Oasis 3DP
Requirements Oasis controller is written in Python. Right now the right Python with libraries is required to run Oasis controller. Install the right python and libraries before running the Oasis controller software. Python 3.6.2 PyQT5 (pip3 install PyQt5)pyserial...

3. Peripherals Setup: TFT Display Control
Instructions from PiCon One
This step describes the TFT display setup for PiCon One. The TFT display I am using is the Adafruit 3.5 480x320 display with product ID 2050. The current pin assignment for this TFT on PiCon One v1.0a is matching the Adafruit 3.5 PiTFT (product ID 2097)....

|<
<
54
55
56
57
58
>
>|