524 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

PiFox
Instructions from PiFox
SettingsFor many settings 0 is OFF / 1 is ONDo not leave any line blank you must manually input all settings. Input the setting then press enter to proceed to the next setting.Callsign:Input your ham callsign. This is required by the FCC and is found...

Step 1: Configuring Wireless Interfaces for Hotspot 2.0 on OpenWRT
Instructions from Configuring Hotspot 2.0 on OpenWRT Devices
In the /etc/config/wireless file, customize the settings for your Hotspot 2.0-enabled interface. Ensure the correct device, encryption type, and other parameters are set. Pay attention to the WAN Metrics, NAI Realm, and Domain Names sections to tailor...

Setting up the Camera module and Smile Detection
Instructions from Water Alarm with RPi
I'm using the 5MP Pi Camera which has a fairly easy setup. Just enable camera in settings and connect the camera to the port (the one opposite to Ethernet input) with its blue part facing the Ethernet. RPi camera module setup For the Smile detection...

PROGRAMMING
Instructions from ESP-01 CONTROL RGB LED CUBE 4x4x4
In my program, ESP-01S ESP8266 is used as a stand-alone device to control a RGB led cube 4x4x4. The project code is available at my GitHub. CONNECTIONThe ESP-01S ESP8266, 74HC595 & TPIC6B595N are connected together as follows: LED CUBE CONTROLFor layer...

3. Programming the WeMos D1 Mini Microcontroller
Instructions from IoT Automatic Dog Feeder
You can follow along with this tutorial and write the code as go or simply download the project code here. 3.1 Blynk Library and Settings At the very top of your main firmware, define Template ID and Device Name before adding...

Step 13: Setting up the object detection model on FireBeetle 2 ESP32-S3
Instructions from Multi-Model AI-Based Mechanical Anomaly Detector
After building, training, and deploying my object detection model as an Arduino library on Edge Impulse, I needed to upload the generated Arduino library to FireBeetle 2 ESP32-S3 to run the model directly so as to recognize the specialized components...

Third Eye for The Blind
Instructions from Third Eye for The Blind
Code + Making the Module for the HandConnect the ultrasonic sensor to the board by using 4 jumper cables.Then connect a 3.7 volt mobile battery to this module.Then connect the elastic band as shown in the figure.At last upload the code to each arduino...

Pi Zero in a NES Controller
Instructions from Pi Zero in a NES Controller
Step 4: Software SetupBoot into RetroPie and then got the settings, make sure it is up to date with the latest version. Enable the gamecon driver and snes controllers, and then goto the shell and make sure that:sudo nano /etc/modulesAdd a line at the...

Prepare for Blynk
Instructions from App Control Bluetooth (BLE) R/C Car with LEDs
After the connections are verified. We are ready to connect with Blynk through BLE. First upload the file Sam_Blynk_RC_Car.ino with Arduino IDE. #define MA1 3 #define MA2 5 #define MB1 6 #define MB2 9 #define BOTTOM_LED 13 #define FRONT_LED...

Testing
Instructions from Analog Signal Generator for Industrial Controls
I tested the signal generator by connecting it to the inputs of a Siemens Logo PLC. I use these PLC's on my Industrial Controls Projects so I am pretty familiar with writing PLC software for them. I always write my PLC software in ladder logic but the...

Get yourself a DOS PC (or DOS VM) with good soundcard support (and a Math Coprocessor!)
Instructions from Atari 2600 development suite for a hackerspace.
For full retro effect, use a 386 or better (and it must have a math coprocessor either added or built in!) I don't think the requirements are very high, just as long as you have some ram, something to store stuff on, a compatible soundcard and a way...

ZRTP Hardphone
Instructions from ZRTP Hardphone
### [ CONFIGURE TWINKLE ]# Register an account on https://ostel.co# Replace "6666" with your username and put your passwd after "auth_pass="echo '# USERuser_name=6666user_domain=ostel.couser_display=user_organization=auth_realm=auth_name=6666auth_pass=xxxxxxxxxxxxxxxxxxxxxauth_aka_op=00000000000000000000000000000000auth_aka_amf=0000#...

Arduino Nano: Rotary Encoder with Visuino
Instructions from Arduino Nano: Rotary Encoder with Visuino
ComponentsOne Arduino compatible board (I use Arduino Nano, because I have one, but any other will be just fine)One Rotary Encoder module I got from this cheap 37 sensors set.4 Female-Female jumper wires

Recommended Tools for Calibration
Instructions from Remoticon: Printing Precisely Demo
Investing in quality inspection tools will ensure repeatable results for years to come. You do not need to purchase high end tools but you should stay away just buying the cheapest thing you can find. 6” Digital Caliper: A digital caliper...

Interfacing the LCD Module
Instructions from RETRO-CM3: A POWERFUL RETROPIE HANDLED GAME CONSOL
As different DPI/RGB interface LCD module may be used in this console, here we take the module used in my own build as example. And if you chose a different one, check the pin definition of your module and just make the connections according to the pin...

|<
<
2
3
4
5
6
>
>|