1645 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"

Electro-Magnetic Enabled Bagpipes
Instructions from Electro-Magnetic Enabled Bagpipes
License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

Arduino GPRS IOT Weather Station
Instructions from Arduino GPRS IOT Weather Station
License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

Cheap-dirty-perfect V-Groove Foam Cutter / Bender
Instructions from Cheap-dirty-perfect V-Groove Foam Cutter / Bender
To bend the foam...Add some adhesive tape on the backside of the foam and you can safely bend it.I learnt this trick from Ed at Experimental Airlines and used the tool to build his Photon glider.

MINI-Zee: a $100 DIY smart drone with the Pi Zero
Instructions from MINI-Zee: a $100 DIY smart drone with the Pi Zero
Bill of Material (US$ - Transport & taxes excl.):Raspberry Pi Zero 5.MPU 9205 (SPI 9 dof IMU) 8.MS 5611 (SPI Baro) 9.PCA 9685 (16 channel PWM Servo Driver) 5. 3.3 v. regulator 1.BEC 3 amps 3.Breadboard, Resistors, Connectors, Misc. 7. AutoPilot: 38.HobbyKing...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
Arduino Mega Code The code in the main control panel is fairly standard except for the part which sends data down the I2C bus to the Adafruit Feather slave. This code can be found in 'void sendData()' below and involves disassembling complex float numbers...

Redtree Hydra: A modular platform for robotics
Instructions from Redtree Hydra: A modular platform for robotics
Share a SensorIf you want to see a complete example of sharing the sensor, check out the share a sensor app:svn co http://www.redtreerobotics.com/svn/redtree-apps/trunk/ redtree-apps cd redtree-apps/share_a_sensoror if you prefer git:git clone https://github.com/redtreerobotics/redtree-apps.git...

OpenLD: Lucid Dreaming Research Platform
Instructions from OpenLD: Lucid Dreaming Research Platform
Programming the STM32F4You can either use the STM32Discovery/Nucleo boards or a dedicated STLink V2 programmer to burn the firmware to the OpenLD board. Just make the necessary connections between the SWD connector on the OpenLD board to the programmer....

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...

Sigma Derby Clone
Instructions from Sigma Derby Clone
Program the betting station)The betting station needs to know the odds of the current race to know what to pay out if you win. It also needs to know the race winner.Once again this is the fun version, so there is no code here for coin in, or cash out.#include...

small micro speakers with a rich soundstage
Instructions from small micro speakers with a rich soundstage
print it, and once done remove all unneeded support materials., also please sand sharp corners down a bitnote: in this project Colorfabb NGEN was used for it's rigidness, but with only 10% infill note2: uploaded the models at 3Dhubs, since i don't have...

Place 2nd blue resistor-Optional
Instructions from Bite-Sized Breadboards: Light Sensor
If your room is dark and it's on all the time, add the second blue resistor to make the photocell less sensitive to light! Move the 10k resistor from B1 to B4, leave B7 in placePlace the other 10k resistor from A1 to A4

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

Infinity Mirror Clock
Instructions from Infinity Mirror Clock
System Design:The circuit is very simple: LED Strip - Connect power to the LM2596 Step Down Adjustable Power Supply Module - ensure you adjust the pot so that the output is 5V; Connect the ground to the common ground; Connect data to pin D5 of the ArduinoTouch...

DIY Data Logger
Instructions from DIY Data Logger
Here's the code for the Spark Core. The programming for this is very similar to an Arduino. Once you go to the Spark website and get your Core setup you just click on the BUILD tab, create a new App and paste in the code and it'll upload the code over...

|<
<
3
4
5
6
7
>
>|