Close

1645 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"

  • Run a Code
  • Instructions     from AC Voltmeter using Arduino
  • int m; // initialise variable m float n; //initialise variable n void setup() { pinMode(A0,INPUT); // set pin a0 as input pin Serial.begin(9600);// begin serial communication between Arduino and pc } void loop() { m=analogRead(A0); // read analog values...

  • The Spinning Spectrometer
  • Instructions     from The Spinning Spectrometer
  • Arduino Code// Arduino code for THE SPINNING SPECTROMETER // // This code is released under the beerware license: As long as you // retain this notice you can do whatever you want with this stuff. If we // meet some day, and you think this stuff is worth...

  • Simple digital watch
  • Instructions     from Simple digital watch
  • Wiring the displayTo Wire the display you just need two wires for communication because it uses a I2C protocol and two for power so 4 in total. The two wires for the communication need to go to pin A4 and A5 and power to power. The wiring:A4 - SDAA5...

  • Joystick module
  • Instructions     from MSX on RC2014
  • This is a very simple module, it contains the two joystick ports and some logic.  It depends on the sound module for the i/o. As per the earlier instruction step, the *R6* of Ed's sound module is required because earlier revisions can't be jumpered...

  • Program
  • Instructions     from Hybrid Sim Yoke
  • Add the library https://github.com/MHeironimus/ArduinoJoystickLibrary to your Arduino environment. Load the following code onto the Arduino (adapted from the excellent article at https://giovannimedici.wordpress.com/2020/10/11/ch-pro-pedals-gameport-to-usb-adapter/ ):...

  • Back Panel
  • Instructions     from Modular Display Clock
  • The components are attached to a baseplate (95(W) x 128(L) mm), which is fitted to the back of the MDE's with M3 X 25mm bolts and 10mm standoffs. Four bolts are fitted through the holes in the Neopixel support board and the standoffs fitted to attach...

  • Arduino Code
  • Instructions     from OBS_IRL_STREAM_DECK
  • It's in the GITHUB! The code comes down the these smaller steps: MQTT handling and Button handling. Let's do button handling first. I made a simple button object with the pin number, button press boolean, and button count. struct Button { const uint8_t...

  • GCODE Commands
  • Instructions     from DIY Inkjet Printer
  • The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

  • Clock in a Box
  • Instructions     from Clock in a Box
  • In order to access A4 and A5 of the Arduino, you will need to solder two (2) headers onto the board (at least on my version). I used male right-angle headers to save space.

  • Mounting the ESP8266
  • Instructions     from LG SJ2 Sound Bar hack
  • I use a Wemos ESP8266 board mounted on a small piece of veroboard to connect the ESP8266 to the relevant pins on the mainboard I2C connector.  In my case I use GPIO12 and GPIO13 (SDA A4, SCL A5) for my interface.

  • Connect all hardware components
  • Instructions     from Bottle pomodoro
  • Connect the accelerometer to the Arduino Mini VCC -> VCC GND -> GND SCL -> A5  SDA -> A4  Don't connect the battery, we will have to power up the Arduino Mini and upload the code first using an FTDI basic USB converter
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday