903 Results for "C%20%EB%B0%94%EC%B9%B4%EB%9D%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%EC%BF%A0%ED%8F%B0%20cddc7_com%20%E2%98%86%EB%B3%B4%EB%84%88%EC%8A%A4%EC%BD%94%EB%93%9C%20B77%E2%98%86%ED%83%9C%EC%95%88%20%EC%9B%90%EC%97%91%EC%8A%A4%EB%B2%B3%E2%91%8A%EC%9B%90%EC%A3%BC%20%EC%9B%90%EC%97%91%EC%8A%A4%EB%B2%B3%E2%94%AB%EC%95%84%EB%9E%8D%EC%B6%95%EA%B5%AC%EC%83%9D%EC%A4%91%EA%B3%84%E3%8E%97%EB%B6%80%ED%8F%89%EB%B0%94%EB%91%91%EC%9D%B4%CC%BC%EB%B0%94%EC%B9%B4%EB%9D%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%EC%BF%A0%ED%8F%B0%ED%9B%84%EA%B8%B0%20soliloquist/"

Resource Monitor
Instructions from Resource Monitor
Solder wires from UBBB to LCD. (Note that uBBB pins are ordered as if looking at the bottom, since it also serves as a generic 32-TQFP breakout board if you flip it upside down). Specific connections are described below:-Connect pins 1, 5, and 16 on...

Testing
Instructions from Eazy Peasy High Voltage Variable Capacitor
Capacitance testing I tested the capacitance range in three ways. 1. Using a commercial LCR meter (Extech 380193)2. Using a NanoVNA set to 30 MHz3. Using an Array Solutions VNA (VNA-UHF )Reliable measurements required careful calibration and testing. ...

RGB P4 Led Matrix Clock based on ESP32
Instructions from RGB P4 Led Matrix Clock based on ESP32
Schematics / AssemblySolder the elements on the printed circuit board according to the circuit diagram, instructions and markings placed on the printed circuit board.Connect the WeMos MiniID1 ESP-32, 16 pin male header using soldering or connectors.Insert...

▇▇▇▇ Optional: Use an Offline Simulator ▇▇▇▇
Instructions from FPGA Bootcamp #1
If you don't want to use EDAPlayground you can download Icarus Verilog or install it from a software repository. If you want to use it, you'll first want to save the files in the file section (design.v and testbench.v) to your working...

GCODE Commands
Instructions from DIY Inkjet Printer
The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

Instructions
Instructions from DIY Ntrip Server and Reference Station Setup
DIY Onocoy Reference Station Setup GuideIn this guide, we’ll walk you through the process of setting up your own GPS Onocoy server using cost-effective hardware options and reliable GPS receivers. Whether you’re interested in enhancing the accuracy of...

Turn on and Troubleshooting Notes
Instructions from Flea-Scope USB O-scope (18 Msps, $13 BoM, WebUSB)
I first visually look for shorts/opens, especially on the QFN or QFP and USB (shorts can be easily reworked with the Kester 2331-ZX flux pen; always clean and dry boards after rework; I use isopropyl alcohol and a toothbrush followed by running water)....

Step 5: Uploading Arduino Codes & Conclusion
Instructions from Spider Robot with Arduino
We have prepared a code for you so that you can move the spider robot without any problems at first. A few commands are ready in the code, but you can revise it yourself ;#include // include IR Remote library #include // include servo library //=====...

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Step 4: Pry out the video glasses from the seems by using a plastic tool or a flat head.

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Time to start putting together the low-side driver board with the CAT4101s. First step is to install the connector on the 11 x 8.5 cm protoboard. This is the spec'ed component, but if you can't find one that size, you can use another one up to 11.5 cm...

Fan controller for Re:Load Pro
Instructions from Fan controller for Re:Load Pro
Make you the PCB and get the components and any standard 60mm 4-wire fan will probably do the job. I used a JMC "6015-12HB APW" that I had lying around. The exact the same fan is readily available on eBay.I used eagle to design my PCB, and the files...

Transformer Build
Instructions from 350 Watt True Sine Inverter
This instruction is for building the transformer. It describes materials and fabrication guidance but assumes the reader has experience assembling magnetics. Additional information can be found in the magnetics zip file and the 'inductors'...

Cabling the MPE device's hardware-components
Instructions from MPE-DIY-Device
Power supply: Ground - GND from Teensy (power-rail as described in the PDF attached) +3.3V - 3.3V from Teensy (power-rail as described in the PDF attached) Joystick 1: VRx - Pin 23/A9 (horizontal control) VRy - Pin 22/A8 (vertical control) SW - Pin 01...

Software
Instructions from Mike's Robot Dog
Making the dog walk is quite the challenge, so here's my approach. I created a drawing showing "standing" leg positions in black and progressive changes in red. The approach is to: 1) lift the left front and right rear legs 2) move the left front and...

ARDUINO CODE
Instructions from SOFT ACTUATOR ORTHOSIS
// Libraries #include #include #include #include #include #include #include "Adafruit_AHRS_Mahony.h" #include //MOTOR // Pins for all inputs, keep in mind the PWM defines must be on PWM pins #define STBY D7 #define AIN1 D8 #define AIN2 D9 #define PWMA...

|<
<
1
2
3
4
5
>
>|