Close

19581 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ 《〈 문의 OIO↗5793↗7458 》〉 ㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

  • Assemble the PCB
  • Instructions     from Flea-Scope USB O-scope (18 Msps, $13 BoM, WebUSB)
  • I usually build the boards with a solder paste stencil (also from pcbway.com) using Chip Quik SMDLTLFP solder paste and a Kester 2331-ZX flux pen and Kester Pocket-Pak lead-free rosin-core solder for any rework; I clean boards after rework with...

  • The fsociety Keyboard
  • Instructions     from The fsociety Keyboard
  • In case you want to reproduce this project. There are several points you have to think beforehand:Making this keyboard doesn't come cheap. Doesn't mean to scare you, but spending the money on purchasing high-end mechanical keyboard might possibly be...

  • Norman, Coordinate
  • Instructions     from Norman, Coordinate
  • Amulet wiringNote: The wires typically used for an electronics project will not work in a costume! Typical project wires can only be bent a couple of times before breaking. They are not made to withstand the constant (even gentle) bending and flexing...

  • BUYING THE PARTS
  • Instructions     from Making the Ultimate Class-E Musical Tesla Coil
  • WARNING: DO NOT PURCHASE IMPORTANT COMPONENTS LIKE MOSFET’S OR DRIVER IC’S FROM GENERAL SHOPPING WEBSITES LIKE AMAZON OR EBAY! MANY PEOPLE HAVE PURCHASED CIRCUIT COMPONENTS FROM SUCH SITES AND FOUND THEY WERE TOTALLY USELESS. DON’T WASTE YOUR MONEY:...

  • ramanPi - Raman Spectrometer
  • Instructions     from ramanPi - Raman Spectrometer
  • Section: 8Components Required:Printed versions of the following 3D Printed Objects from the gitHub respository:(1x) optics_module_testStand_laserWflangeA Completed Spectrometer532nm 5mw Laser PointerPocket FlashlightClick on the graphic above to...

  • Raspberry Pi 3 Gameboy
  • Instructions     from Raspberry Pi 3 Gameboy
  • 3. Preparing the Mini USB breakout boardThe Mini USB breakout board doesn't fit in the original spot for charging the gameboy, it's just a little to bulky, so we have to trim it.For that I recommend using a hacksaw:Some pins might get cut off, but that...

  • Finish the modules
  • Instructions     from PolyMod: modular digital synthesizer
  • Each module needs a face plate, which should measure around 150mm by (max) 38mm, although you may want to make slightly narrower modules (e.g. 35mm) to make sure there's a bit of wiggle room between them. Once you've cut your blank face plates, you will...

  • Wooden Clamp Triggers
  • Instructions     from Motion Sensing Lightsaber Game Controller
  • I managed to find just one switch for the buttons, so I had to improvise the other with these wooden clamps triggers. Split apart the wooden clamp, saving the metal clip for reassembling, and mark two spots with a pen for hammering the nails. Hammer...

  • Procedures
  • Instructions     from RTL8722DM / RTL8722DM MINI BLE HID Mouse
  • Open the example, “Files” -> “Examples” -> “AmebaBLE” -> “BLEHIDMouse”.Upload the code and press the reset button once the upload is finished. Immediately after reset, the board will begin BLE advertising...

  • Simple Edison Breakout Board
  • Instructions     from Simple Edison Breakout Board
  • The 70pin headers are slightly fiddly to solder on the board but not impossible to do by hand.The key to this is a lot of flux.Place the board on a flat surface and then using a flux pen, wet the connector area with flux. Then carefully place the connector...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday