Close

12499 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸S선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§8fetch"

  • Ultra Simple 2x4 Server Rack

  • Have them cut the boards for you to these specs:Board #1 and 2: 20.75", then 20.75", then the remainder should be cut in half (will be 27.25" each, minus whatever is converted to sawdust)Board #3 and 4: Just saw these in half: 48" long.This will give...
  • The weight

  • Keeping the screen tensioned is what keeps it flat. I provided the needed tension almost all in the vertical axis with weight. Take a scrap of your screen fabric, and test how hot you can get an iron on it, before it melts. Three layers, and two are...
  • Painting the fabric

  • The light block fabric is actually three layers. White on both sides, with black plastic in between, but you are still painting fabric so you may have to experiment to get it right. Lay your light block fabric out on some hard clean surface. Don't step...
  • The roller

  • Cut your fence post a few inches longer than your screen width. Deburr the edges, inside being just as important. Make 2 hardwood, Lexan, or acrylic blocks to plug the ends and accept your threaded rod. Being centered and true is important, or your whole...
  • Joining the two

  • Get help. Clean yourself. Clean the floor. Wash your hands often. Look for the weld line on the post, or otherwise establish a line along it's length. Line up your fabric with this line, and tape across the joint, applying slight tension the the fabric....
  • The motor

  • Take your other coupler nut, and fashion a small post coming off of it at a 90 degree angle. I welded mine. Take your corner brace, and make a second post behind the first, the thickness of the corner brace, so the main post slides on the front, and...
  • Trimming the screen

  • Run the motor in the 'screen up' direction. Take a brand new, sharp razor knife and hold it against un-even ends of the rolled up fabric. Make sure the direction of travel of the material is going away from you, so the knife does't bind in the cut and...
  • The control circuit

  • The relay coil is driven by 'remote power' output on the projector. There are no other connections made to the coil. As such, this also performs the needed isolation so if you screw up anything else, you at least don't fry your projector. The projector...
  • Final assembly

  • Put it up on the wall and level it.  One day in the sun will remove any wrinkles, or careful application of a hair dryer will do the same.  Don't overheat it as the plastic inside can expand and ruin it.Tweak the stop positions.  Applying...
  • LED Hoodie

  • Sew the gemma onto the hoodie in a location that is relatively close to where you are putting the leds.I put it on the inside of the left half of the hoodie.Make sure you read adafruit's guide on sewing with conductive thread, especially the part about...
  • LED Hoodie

  • Possible improvements coming:Adafruit just released a heartrate sensor, that could be fun to add into this project.Accelerometer could also be nice to add in.GPS?  Maybe so, not sure how that would work though.
  • Smile Station

  • First I got the RPI set up with the latest and greatest Raspian. Make sure that you up-date up-grade and set the GPIO and Camera in raspi-config. This site has all the information that I started off with even the code I used to get it working at first...
  • Smile Station

  • On this next link is where I got the info for sending the photos taken with its own email account .http://mitchtech.net/connect-raspberry-pi-to-gmail...I tested it by copying the script to send attachments in to the python editor on the rpi by first...