Close

60 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"

  • Basic tips and tools
  • Instructions     from Making your work social media ready
  • - Do not put graphics over your photos, or, make sure I can crop them out. I **WILL** tag you if the information is available, but I won't share your watermarked image.  - Clean your lens.  Especially if you're photographing...

  • Dirt Barrel
  • Instructions     from Dirt Barrel
  • The inlet is built in a similar way.A piece of PVC pipe is prepared with some slots to allow clamping of the inlet tube:The pipe is held by two square pieces of plywood, four screws and a 90 degree bend is attached on the inner barrel side:I also sealed...

  • Align cutting wire.

  • Instructions     from Super simple foam cutter
  • Place the bottom framing with the tension bolt into the rest of the framing. Tighten the nichrome wire around the top of the bow with enough tension that the wire is tight.  The wire gets hot and PLA doesn't like hot so you should use a locking...

  • LED Polyhedron
  • Instructions     from LED Polyhedron
  • Build the first faceAlign two edge segments' ends at the appropriate angle, to create the first vertex of the polyhedron. (see table)Solder the vertexComplete the first face by adding more edge segments until a ring is formedFace shapeInner angleTetrahedronTriangle△3x...

  • Bench Power Supply
  • Instructions     from Bench Power Supply
  • PCB Rev 1.0 Errata:Diode D3 is reversed in the board silkscreen. Place it backwards (opposite of what is shown) for a positive supply, and normal (as shown on the silk screen) for a negative supply. Rev 1.1 has been changed to be correct.Crystal X1 is...

  • Circuit Design
  • Instructions     from Analog Signal Generator for Industrial Controls
  • The heart of the design is the LM358 Dual Operational Amplifier (Op Amp). An Op Amp amplifies a signal and has a couple of main advantages over just using a BJT transistor as an amplifier because it has a very high input impedance (resistance) and a...

  • Mechanical build
  • Instructions     from VSTiBox
  • Warning: if you want to build your own VSTiBox, please consider that the v1.0 design files contain some errors, but a manual workaround is possible. During the build process of my VSTiBox I came across a number of design mistakes which I have tried to...

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts.  The progression of construction was arranged so that each stage could be completed and tested...

  • BigFDM Building Manual
  • Instructions     from BigFDM
  • Before starting BigFDM is a big machine, and therefore requires a large space were you can comfortably build it. This especially when you need to move around it, or to install big parts. Furthermore the build requires the use of common tools, including...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday