18888 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》레깅스룸견적よ레깅스룸ago레깅스룸メ강남레깅스룸eighty 선릉레깅스룸κ선릉레깅스⒲레깅스룸メｃ선릉레깅스룸literary"

Wearable computer
Instructions from Wearable computer
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
On the raspberry pi, you may need to affix the battery pack to the pi. I recommend a rubber belt (of the variety used in small vacuum cleaners); however, several rubber bands will do.I recommend taking some foam and cutting a rectangular hole slightly...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
Take a 20 gallon storage tote. Using hot glue, fit mylar coated bubble wrap around the interior of the enclosure, and the interior of the cover.Cut insulation carefully to allow container to close easily.

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
(These are the areas I wing it.)Get a board slightly larger than the footprint of your fluorescent lamp.Layout your junction boxes approximately how you'd like them to sit.

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
When the junction box is roughly where you want it, collect a relay, and place it in the bottom of the junction box.Using self-drilling dry-wall screws, drill through the hole in the heat sink of the relay, through the junction box, and into the wood. ...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
If you can't safely wire 120VAC, please stop here. I bear no responsibility for any bodily injury, death, or loss of property as a result of mimicking this project.Wired 120VAC through the Solid State Relays, outlets, and switches shown in the schematic.Within...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
Apply Code to Arduino...

Light Emitting Ball (LEB)
Instructions from Light Emitting Ball (LEB)
Laser Cut Acrylic (2.6 mm thick I believe, but you can double check the slot measurements in the DXFs to be sure) Accordign to the following DXFs.https://drive.google.com/file/d/0B_2xkbzRozdxbHZLQ...Solder the ends of each ring of WS2811's together,...

Project 13
Instructions from Project 13
Install the software to your Hard Drive.

Project 13
Instructions from Project 13
Read the Project 13 - Installation and Setup.pdf to setup an instance of the program of your own and get started trying out Project 13.

Homamade carbon tape Taser-proof clothing
Instructions from Homamade carbon tape Taser-proof clothing
It's strange why taser has such an imperfect design (I mean a real taser, not a stungun), from which so easy to defend ...A little later I'll write a project how to easily improve any taser that it could overcome my or any other protection:)

Keyboard with Apple Mouse Scroll Ball
Instructions from Keyboard with Apple Mouse Scroll Ball
Use a dremel to make the hole in the top plate

Keyboard with Apple Mouse Scroll Ball
Instructions from Keyboard with Apple Mouse Scroll Ball
Dremel also removes material on the back side of the plate so that the ball is close to the surface.

Keyboard with Apple Mouse Scroll Ball
Instructions from Keyboard with Apple Mouse Scroll Ball
You can swap a hub's shorter USB cable for the long one the keyboard comes with.

|<
<
4
5
6
7
8
>
>|