1380 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격ｕ 쓰리아워가격earth강남쓰리아워강남쓰리아워쓰리아워enter 강남쓰리아워ぶЪ강남쓰리아워most"

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 2 - Import the Arduino board file into Altium Designer: Using Altium Designer (AD) requires that I import Eagle board into AD. AD14.x includes an Eagle importer. Used source files from the Arduino site to import in AD.

Setting up Linux AVR and ARM toolchains
Instructions from Setting up Linux AVR and ARM toolchains
INSTALLING MINT ON A RELUCTANT TOSHIBA SATELLITE LAPTOPDownloaded the latest Linux Mint 16 with Mate image via torrent from linuxmint.org. Burned to DVD and used it to boot the Toshiba. All seemed to be going well untill the boot finished and I tried...

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 2 x 22pF Supporting Capacitors for the Crystal Oscillator

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 3 x 220 Ohm Resistors (the 3 resistor spots nearest to the Crystal Oscillator)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder 3 x 3mm LEDs (Top is Yellow, Bottom Left is Red, Bottom Right is Green)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Connect the bottom-center + and - connection terminals to a 3V power source (CR3023 Battery, 2 x AA Battery, ..)

Awesome Jacket
Instructions from Awesome Jacket
The kill switch was constructed using a short piece of 1.5" ABS plumbing tube and two end caps. Through one end cap I ran a multi-wire cord that carried 5V and the switch cct; to the other end I connected a stereo plug to match the jack described above....

TI Launchpad Arcade Control to USB Interface
Instructions from TI Launchpad Arcade Control to USB Interface
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...

Peril-Sensitive Sunglasses
Instructions from Peril-Sensitive Sunglasses
Accelerometer is wired like this:In my case I used:Analog 0 = X axisAnalog 1 = Y axisDigital 2 = 0g Detected

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #6 too, option of hard or soft enclosure): Use a 12" piece of 3" clear diameter heat shrink tubing to cover the board, the cut out the USB-mini connector with an X-acto knife, and mount rubber bumpers such as Digikey part # SJ5748-0-ND...

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
The first step to a good coffee brewing robot is to figure out how to brew good coffee. I've got some tips and tricks to brewing good coffee in the project logs ("A Dive Into the World of Coffee"), so I'll get directly into how I achieve good, full bodied...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

1
2
3
4
5
>
>|