2035 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸Ｓ선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§８fetch"

Lightbar
Instructions from Lightbar
Python Code. This reads a text file modified by the web server and then updates the image buffer. Handles button presses and sending the data to the Teensy/light strip. My python knowledge isn't the best so I'm sure there was a better way to do a lot...

littleBits Halloween Creepy Portrait
Instructions from littleBits Halloween Creepy Portrait
Next you will need a frame and portrait to hack. We suggest you use a frame that is deep enough to embed the servo (~1.5"). We used an 11" x 14" x 1.5" wood frame from Blick. You can use a portrait from your house or you can print out version we used....

littleBits Halloween Creepy Portrait
Instructions from littleBits Halloween Creepy Portrait
Cut three layers of ¼" foamcore to sit underneath the eyes so that they sit closer to the portrait and at a similar height to the servo arm. The dimensions of our layers are 4.5" wide x 5" tall. Glue the three layers together.

littleBits Halloween Creepy Portrait
Instructions from littleBits Halloween Creepy Portrait
Cut out where you just traced with an X-acto knife (you may want to make the cutout slightly bigger than the tracing). Then cut two pieces of ¼" thick basswood to mount the servo to. Flank the sides of the hole you just cut with the two pieces of...

Inexpensive Composite Propellers/Rotors
Instructions from Inexpensive Composite Propellers/Rotors
Preparing the Material Blanks for the RouterCut the Foam PiecesCut the foam sheet to sizes needed to build up the foam block. The propellers for Goliath use 10" x 38" pieces. To get the most out of the material use the cutting guides.Peel off the coating...

Inexpensive Composite Propellers/Rotors
Instructions from Inexpensive Composite Propellers/Rotors
Cut the Propeller BlankTools: CNC Router with 1/2" and 1/4" router bits (flat)A) Attach the Block and prep the routerAttach the blank to the spoilboard. When cutting with the half inch bit, there is an extra 3/4" on each side of the block, but make sure...

Ultimate Universal Remote
Instructions from Ultimate Universal Remote
12.) Connect all remaining wires and fit board into battery compartment

Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Instructions from Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Use P3_0 and P3_1 to communicate with the ESP8266 RX/TX via a 5v<>3.3v shifter., add UART component and config to 11500kbps, 1024 rx buffer, 128 tx buffer (or less) default everything else.Add a X to 3.3V VREG and power the ESP8266 and level shifter.Make...

PiFox
Instructions from PiFox
Installation on RaspbianThe Festival package is required for text to speech and WiringPi package is required for GPIO use.1. Update Pi and install git, festival, and wiringpi packageUpdate Pi"sudo apt-get update""sudo apt-get upgrade"Install Git on...

NeuroBytes
Instructions from NeuroBytes
Reflow.I use a modified toaster oven to reflow NeuroBytes, usually 8 or 12 at a time. It's not perfect; I usually watch the parts through the oven's window and sometimes need to manually extend the cycle to ensure everything reflows properly. I also...

Apache AL13P & TL-320b - One Pass PCB Toner Xfer
Instructions from Apache AL13P & TL-320b - One Pass PCB Toner Xfer
Building the Add on PCB is simple, just a few parts. You can test your build by applying 12V+ on pin 4 and a ground on pin 3 of the 6pin inline wire to board pads. The Beeper should emit a 1 second beep. Building the CAT5 (15") 6pin cables to attach...

Good Morning Sunshine
Instructions from Good Morning Sunshine
Step 3: Glue Together the Servo MountNext, glue two of the D strips together to create a .5" x .5" x 2.75" block. Repeat this with the other two D strips. When they are both dry, glue them to the back of panel A as shown in the assembly diagram. The...

Good Morning Sunshine
Instructions from Good Morning Sunshine
Step 12: Automate It with IFTTTNow that your wakeup machine is all set it, it's time to automate it with IFTTT. If you want to wake up with the sunrise, your recipe would look like this: WHEN the sun rises (and we're pretty sure it will), THEN activate...

littleBits Smart Home Good Morning Sunshine
Instructions from littleBits Smart Home Good Morning Sunshine
Step 3: Glue Togetehr the Servo MountNext, glue two of the D strips together to create a .5" x .5" x 2.75" block. Repeat this with the other two D strips. When they are both dry, glue them to the back of panel A as shown in the assembly diagram. The...

littleBits Smart Home Good Morning Sunshine
Instructions from littleBits Smart Home Good Morning Sunshine
Step 12: Automate It with IFTTTNow that your wakeup machine is all set it, it's time to automate it with IFTTT. If you want to wake up with the sunrise, your recipe would look like this: WHEN the sun rises (and we're pretty sure it will), THEN activate...

|<
<
5
6
7
8
9
>
>|