Close

347 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た 《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

  • Assembling right side
  • Instructions     from BrailleRAP DIY Braille embosser
  • Fix 3d printed parts BOTTOM_AXIS_right and TOP_AXIS_right on the frame with M3 washers M3 Nyl nuts and M3-14 Fix 3D printed parts KP08_support and KP08 on the frame with M5 washers M5 Nyl nuts and M5-25 screw Fix a KFL08 with M5 washers...

  • Prepare X and Y motor supports
  • Instructions     from BrailleRAP DIY Braille embosser
  • Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...

  • Mounting & Other Stuff!
  • Instructions     from Coin Cell Power Guide
  • Mounting:One hole sized for 4-40 screws (or M3).  Screws and standoffs not included.Other Cool Stuff:There are test points a-plenty, just to help you troubleshoot stuff.  Or you can solder wires to them and pull extra power lines off the badge...

  • FarmBot - Open-Source CNC Farming
  • Instructions     from FarmBot - Open-Source CNC Farming
  • Gantry Assembly 2 hoursThis is the estimated time it will take to assemble the Gantry.Step 1: Assemble the Gantry PlatesGather and lay out all of the parts. You will need:Two Gantry PlatesEight complete V-wheelsEight M5 x 30mm screwsEight M5 locknutsEight...

  • Instructions:
  • Instructions     from Laser XY Scanner
  • Step 1: Gather Your Components Laser XY Scanner - BOM I usually like to source my parts from DigiKey, but the low-cost options on Amazon are hard to beat sometimes. This list is just one of many sources for each component in the BOM. There are of...

  • Experiment Bioroid!
  • Instructions     from Experiment Bioroid!
  • Wheels to servo connectionsandpaper wheelSuper Glue each wheel to servo horn (included with each HS-322HD servo)use center tool(m3 bolt with tape/spacer) to align horn on center.

  • Animatronic Hand
  • Instructions     from Animatronic Hand
  • Upload the “Rock Paper Scissors” sketch onto your Arduino. The sketch file can downloaded from this page in the "other files" section.2.  Create the circuit.3.  Build the robotic hand. Laser cut the attached file “robotic...

  • Clone of stEve
  • Instructions     from Clone of stEve
  • - On D push four M3 nylon screws 25mm long through from back (side with graphic), add spacers (acrylic donuts) on three and nylon nut on top right (when looking from front) then place Arduino on top.- To the three screws apply a stack of five spacers...

  • FarmBot - Open-Source CNC Farming
  • Instructions     from FarmBot - Open-Source CNC Farming
  • Cross-Slide Assembly45 minutesThis is the estimated time it will take to assemble the Cross-Slide.Step 1: Gather the PartsGather all the parts you will need for the Cross-Slide and lay them out in a logical manner. You will need:One Cross-Slide plateSix...

  • Fan controller for Re:Load Pro
  • Instructions     from Fan controller for Re:Load Pro
  • Find 3 thin wires for the fan and test that it can get through the small hole in the heat sink, and solder them to the PCB.Now it is time to solder the PCB to the expansion slot.Glue the temperature sensor to the heat sink and get the 3 fan wires through...

  • BANANANAS
  • Instructions     from BANANANAS
  • First mount the 2,5" Sata HDD with M3 screws onto the buttom plate of the case. The red lines in the CAD drawing indicate the position of the HDD and the Banana Pi.
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday