Populate the board. You will need some good experience with 0805 SMD soldering, and some tools like soldering iron and hot air rework station. Start with the bottom side, with the microcontroller, the other ICs and finally the small passive components....
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...
Step 2 - Import the Arduino board file into Altium Designer: Using Altium Designer (AD) requires that I import Eagle board into AD. AD14.x includes an Eagle importer. Used source files from the Arduino site to import in AD.
Step 3 - Build major footprints: Costing the available board area requires building the major footprints and placing them on the PCB. Built early footprints and placed to determine what additional space is avail. Files in git.
Labview and Arduino IntroductionLabVIEW (short for Laboratory Virtual Instrument Engineering Workbench) is a system-design platform and development environment for a visual programming language from National Instruments.To learn about LabView check official...
Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...
This is the code I used for the right frame in the first picture.#!/usr/bin/perl#use CGI qw/:standard/;use URI::Escape;my $cols = 3;my %button_codes;$button_codes{'1'}='BTN_1';$button_codes{'2'}='BTN_2';$button_codes{'3'}='BTN_3';$button_codes{'4'}='BTN_4';$button_codes{'5'}='BTN_5';$button_codes{'6'}='BTN_6';$button_codes{'7'}='BTN_7';$button_codes{'8'}='BTN_8';$button_codes{'9'}='BTN_9';$button_codes{'0'}='BTN_0';$button_codes{'Ch-'}='KEY_CHANNELDOWN';$button_codes{'Ch+'}='KEY_CHANNELUP';if...
And this is the left frame. flowplayer href="http://xxx.xxxxxx.org:8080/stream.flv" style="display:block;width:320px;height:240px" id="player"> flowplayer("player", "flowplayer-3.2.11.swf");
If you walls are textured, you'll need to texture the wall to match. If you have a special texture (other than spray like mine) you might practice on a scrap board as you want this to match seamlessly.
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...
The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...
Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...