Close

40 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • The Rocket
  • Instructions     from SpaceX Falcon 9R Lamp
  • For me, the print time ran about 10-11 hours for everything, but it could be upwards of fifteen hours. At this point you should have 3D printed: Leg Left Half x4Leg Right Half x4Interstage x1Grid fins x4Engine Block x1Leg Tips x4 With all of the 3D printing...

  • Assemble your Printer
  • Instructions     from The Trash Printer - Version 3
  • You can check out the interactive model for the Trash Printer on the SketchUp 3D viewer, or download it from the SketchUp 3D warehouse. You can use this model as a reference to see how all the parts go together, and you can also use it to modify...

  • Raspberry Pi 3 Gameboy
  • Instructions     from Raspberry Pi 3 Gameboy
  • 12. Gluing in the analog sticks and programming the leonardo pro microI glued in the analog sticks and soldered the corresponding wires to them. I then wrote a program to turn the leonardo into a USB joystick with 14 buttons and two analog inputs and...

  • Raptor12 Wireless AC Dimmer

  • Instructions     from Raptor12 Wireless AC Dimmer
  • Back of ACLogic:Make sure you assembly from the correct side:)Solder the atmega(expand)Microelectronic stuff:atmega328p 22pf cap x216Mhz CrystalAxial Components:4.7KOhm Resistos x1310ohm x11MOhm x1120kOhm x33kOhm 1x22k 1x5.1v Zener x2Transistors and...

  • Raptor12 Wireless AC Dimmer

  • Instructions     from Raptor12 Wireless AC Dimmer
  • This is a .22uf capacitor, this is non polerized ceramic so it can go ether direction. This helps controle the clipping voltage of the main fet.C3 and C4 are small .22pf theses are not the same as the perviose step. Theses capacitors setup the imedance...

  • 1Charger
  • Instructions     from 1Charger
  • Calibration1.   #define CALIBRATION in software and recompile and flash ATtiny8612. For each range make two measurements in order to calculate the line v=k*ADC + m. With this simple approach I get about  10-20mV and 10-20mA accuracy ( compared...

  • The Tinusaur
  • Instructions     from The Tinusaur
  • Please go to the Tutorial 001: Blinking LED x1 to learn how to write a simple program that will make a LED blink.

  • Bench Power Supply
  • Instructions     from Bench Power Supply
  • PCB Rev 1.0 Errata:Diode D3 is reversed in the board silkscreen. Place it backwards (opposite of what is shown) for a positive supply, and normal (as shown on the silk screen) for a negative supply. Rev 1.1 has been changed to be correct.Crystal X1 is...

  • MAPone
  • Instructions     from MAPone
  • NOTES:Assemble the parts in the order in which they are listed on the assembly drawing.Cap C2 is polarized - verify before solderingDiode D1 is polarized and mounted vertically - verify before soldering.LED's D2, D3 are polarized - verify before soldering.LED's...

  • Purchasing Electronics/parts
  • Instructions     from Jeremy The Butler Bot
  • First step to build Jeremy is to purchase all the materials. You will need the followingElectronics:X1 Adafruit Wave shield (https://www.adafruit.com/product/94)X1 Arduino Mega (https://store.arduino.cc/usa/arduino-mega-2560-rev3) (note: any Arduino...

  • JACK
  • Instructions     from JACK
  • Solder components on the boardI'll follow the following order (probably going to change as I still have to do a prototype):IC2, X1, C13, C12, C2, C4, C3, C9, C1, R4, C6, L1, L2, C7, C5, R2, J1, IC1, D2, R2, R3, R1, SW1, R5, C8, C11, IC3, C10, D1, D2,...

  • Pi0Plane
  • Instructions     from Pi0Plane
  • Step 10: Testing the center of gravity.The last thing we have to do is some tests to know if it is well balanced. In the first test, we are going to test the pitch by using the 2 circles that we can see under the wings of the plane. We are going to put...

  • WiFi World Clock
  • Instructions     from WiFi World Clock
  • X-8266 x1X-OLED x118650 battery shield V2 x1Simple 3D printed case X1You can have a look at the pin map.SDA is connected to D1.SCL is connected to D2.This two pins work as the IIC pins.The other pins can be connected to other sensors.The X-8266 can really...

  • Finish the mechanical build.
  • Instructions     from InspectorBot
  • Insert five additional wires through the grommet on the top cover of the box. I cut over-sized wires so I can cut them to size later. The colors do not matter, but I like to have one red wire for the positive connection. On the top cover of the Raspberry...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday