5651 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워ｈ 쓰리아워worship쓰리아워레깅스룸쓰리아워가격강남쓰리아워egypt 강남술집정보クＱ강남쓰리아워disorder"

Portable environmental monitor
Instructions from Portable environmental monitor
Populate the board. You will need some good experience with 0805 SMD soldering, and some tools like soldering iron and hot air rework station. Start with the bottom side, with the microcontroller, the other ICs and finally the small passive components....

Buy a Psion Organiser II
Instructions from Getting online with a 1987 Psion Organiser II
Start with the fun bit! Here's a short Organiser II buying guide I produced myself - consult the websites for more detailed/informed insights... There are four models of Organiser II - all should work with this project. I own two Organisers - a 1988-89...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 2 - Import the Arduino board file into Altium Designer: Using Altium Designer (AD) requires that I import Eagle board into AD. AD14.x includes an Eagle importer. Used source files from the Arduino site to import in AD.

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 3 - Build major footprints: Costing the available board area requires building the major footprints and placing them on the PCB. Built early footprints and placed to determine what additional space is avail. Files in git.

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 8 - Break out IO pins and port (off-sheet) to top level in project hierarchy.

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Unscrew the circuit board and pull off the RF shield. Be carefull because once you take the board out there will be nothing holding the buttons in.

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Now is a good time to cut your EL panel down to size. Lay the LCD on top of it and trace around it with a marker. I chose to have the leads going out the right side (facing the front of the screen). You can cut the EL panel with scissors. You might want...

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Find a good place to mount the push button that will control the backlight. I chose to put mine on the left side of the calculator, as you can see in the pictures. This was a very tight fit though. Some other suggestions would be on the top or under...

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
If you walls are textured, you'll need to texture the wall to match. If you have a special texture (other than spray like mine) you might practice on a scrap board as you want this to match seamlessly.

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...

Wearable computer
Instructions from Wearable computer
Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...

Wearable computer
Instructions from Wearable computer
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

1
2
3
4
5
>
>|