1975 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗셔츠룸퍼블릭ㅖヲfist퍼블릭술집ヅ퍼블릭룸셔츠룸퍼블릭∵ ⒜셔츠룸퍼블릭counsel 퍼블릭룸в퍼블릭술집５₁element"

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Mini Potato Cannon
Instructions from Mini Potato Cannon
9.) Shove both wires into the holes in the cap, make sure they are close enogh to spark, and tape or glue them in place.

Mini Potato Cannon
Instructions from Mini Potato Cannon
9.) Shove both wires into the holes in the cap, make sure they are close enogh to spark, and tape or glue them in place.

Animatronic Iron Man MKIII suit
Instructions from Animatronic Iron Man MKIII suit
Notes about tools and materials used:ProPoxy 20 is awesome stuff. When making the brass tube pivots for the shoulder rocket pods it was easiest to glue the brass tube to the servo casing with superglue ( I use Gorilla glue with a spray accelerator) and...

Late Night Reading Lamp
Instructions from Late Night Reading Lamp
Solder LEDs, resistors etc onto a bit of veroboard. I used a female PCB header for plugging in the battery so that I didn't have to route long cables around the frame. Leave some length on the LED pins so that they stand up a bit from the veroboard

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #5, option of hard or soft enclosure): Make an enclosure out of a Hammond 1455N1602 case (Digikey part # HM980-ND). This case has plastic end panels which you can easily modify with a hot knife, file, etc. For the front panel you can print...

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
Effective Bardware Based Stepper Motor ControlIn my quest to derive a robot control scheme from scratch, I've been working to figure out how to control a stepper motor. Stepper motors are great because they're cheap, relatively simple to control,...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

Trombino
Instructions from Trombino
Use epoxy to glue the tower to the potentiometer casing. If using a wind sensor solder long wires to the V+, GND and OUT pins of the wind sensor. Seat it in the gap it magically fits perfectly into as shown below. Tidy your cables! I pleated mine and...

LabSeries L7 Guitar Amplifier RFI Fix
Instructions from LabSeries L7 Guitar Amplifier RFI Fix
After you find out the side that is causing the problem, wrap the offending wires with the foil. This creates a makeshift shield as long as the foil is grounded to the chassis

LabSeries L7 Guitar Amplifier RFI Fix
Instructions from LabSeries L7 Guitar Amplifier RFI Fix
If you want to keep the amp original, and not replace wire, you can leave this foil in place. This is fine as long as the amp isn't really moved. However, if you move the amp around you will want to replace the foil with something a lot better....

Making a BR-900CD Stand on its own
Instructions from Making a BR-900CD Stand on its own
After reminiscing about my audio recording gear, I started thinking about a stand that I had purchased with the express idea of mounting the BR-900CD onto. It was a heavy duty music stand that I had picked up on sale for 20 dollars. After I got it home,...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
Assembling the tube1And now for assembling the laser tube itself. Things needed for this will be a bit of JB weld, a long thin dowl that fits inside your mirror mounts. This will help align them, much better than eyeing it. You will also need some 3/8th...

|<
<
2
3
4
5
6
>
>|