Close

854 Results for "%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F%3E %EA%B0%95%EB%82%A8%EC%85%94%EC%B8%A0%EB%A3%B8 %E2%88%88%EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5 %E2%88%83%EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%8F%EA%B0%95%EB%82%A8%EB%A3%B8%C2%B1 %EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5 %E2%88%91%EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1 %EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%80%EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8%2B %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1%E2%88%86 employee"

  • Fan controller for Re:Load Pro

  • Make you the PCB and get the components and any standard 60mm 4-wire fan will probably do the job. I used a JMC "6015-12HB APW" that I had lying around. The exact the same fan is readily available on eBay.I used eagle to design my PCB, and the files...
  • Header Pins

  • Solder on the 3 sets of three pin headers for the i2c address (A0, A1, and A2). You'll need to attach a jumper to each one to pull the pin high or low (chip will not work if these are left floating). The remaining header pins are optional depending...
  • Run a Program

  • int x;int y;void setup() { pinMode(2,OUTPUT); pinMode(3,OUTPUT); pinMode(6,OUTPUT); pinMode(A0,INPUT);} void loop() { x=analogRead(A0); y=map(x,0,1023,0,255); analogWrite(6,y); digitalWrite(2,HIGH); digitalWrite(3,HIGH);}
  • Run a Code

  • int m; // initialise variable m float n; //initialise variable n void setup() { pinMode(A0,INPUT); // set pin a0 as input pin Serial.begin(9600);// begin serial communication between Arduino and pc } void loop() { m=analogRead(A0); // read analog values...
  • Unruly signals: S.O.S....

  • SignalPinPortActionDescriptionRESETNJP4.14External reset control+3V3JP4.13Digital power lineAREFJP4.12Fixed at 3.3VHVIJP4.115V supply for laser and APDLASER_POWERJP4.10A0DACSet laser powerTHRESHOLDJP4.9A1DACComparator thresholdBIAS_VOLTAGEJP4.8A2ADCAPD...
  • NANO-4096

  • Finally screw the spacer onto the joystick breakout boardSolder the joystick onto the perfboard and connect VCC (5v) and GNDConnect the X pot to A1 (Since the board is rotated X becomes Y)Connect the Y pot to A0Key is not connected
  • Assemble the Four Adafruit Trellis Modules

  • Solder up the four Adafruit Trellis modules.  If desired, add LEDs to the top side of the board.  The orientation for the LEDs is noted on the silksreen on the top side of the board.  For more reinforcement, bridge the connections between...
  • Construction of Display

  • Solder headers to OLED Wing.  Do not solder Wing to Feather yetMake connections from NeoPixel Strip and Gas Sensor to OLED WingWing to FeatherGND and 3VSCL and SDA to connect I2C bus  Buttons: Button A - A8 Button B - A7 Button...