Close

807 Results for "%EA%B0%95%EB%82%A8%EC%85%94%EC%B8%A0%EB%A3%B8%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F %E2%88%8F%EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8 %3E%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E2%88%88 %EA%B0%95%EB%82%A8%EB%A3%B8%E2%88%82 %EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5%E2%88%81 %EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1%3C %EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5%E2%88%80 %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1%C2%B1 %EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%86%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC every"

  • Run a Program
  • Instructions     from Clap Switch with the help of Arduino
  • const int analogInPin = A0; // Analog input pin 0int sensorValue = 0; void setup() { DDRD = 0xFF;} void loop() { sensorValue = analogRead(analogInPin); //read ADC value on channel 0 if(sensorValue>60) { PORTD ^=(1<

  • Soldering the CPU
  • Instructions     from 68020 minimal homebrew computer
  • Start by soldering the CPU; it can be done with a regular soldering iron. Refer to the internet for guidance on soldering this SMD component (SMD soldering tutorial). The trick is to use flux (and very little tin). For me, this was the first time I soldered...

  • Understanding how to disconnect the speaker
  • Instructions     from Hush Owlet
  • moThe big black device in the middle of the printed circuit board (PCB) is the speaker (aka buzzer, or transducer). You can see a little slit in the one side where the sound comes out. There is a back side to the circuit board that you cannot easily...

  • Honeybee Hive Monitoring
  • Instructions     from Honeybee Hive Monitoring
  • Add the HX711 sensor board to the Apitronics Bee.Connect the 4 wires from the scale to the 9-pin plug that passes through the weatherproof enclosure. These wires should be connected on the inside of the enclosure to E-, E+ (for excitation + and -) and...

  • Clone of stEve
  • Instructions     from Clone of stEve
  • Breadboard circuit- The light follower circuit for the workshop is made up of two LDRs in voltage dividers with 22kOhm resistors (VCC - LDR - {signal to A0} - Resistor - Ground), (VCC - LDR - {signal to A1} - Resistor - Ground).- Additionally we supply...

  • 68000 Processor
  • Instructions     from Nomad
  • Plug in the 68000 processor and minimal glue logic. To test if you build this part of the circuit correctly, add 10k pulldown resistors on all 15 data lines of the processor.  Power on the board, and verify with an oscilloscope that A0 operates...

  • Assembly Steps
  • Instructions     from Arduino Joystick Mouse
  • Print enclosure and file down inner tracks so that the joystick PCB slides in easily De-solder pins from joystick breakout board Use wires to make the following solder connections: Solder GND on Joystick to GND on Arduino Solder 5V on Joystick to VCC...

  • Arduino Code
  • Instructions     from Arduino Negative Voltmeter
  • // i2c and u8g library for 1306 oled display #include #include "U8glib.h" #define R_LOW 100 // 100k or 10k resistor, 1%, smd1206, 1/10 watt #define R_HIGH 5000 // 5M or 500k resistor, 1%, smd1206, 1/10 watt #define AREF 1.1 // Aref pin voltage #define...

  • Code
  • Instructions     from Soil Moisture Sensor
  • #define SensorPin A0 float sensorValue = 0; void setup() {  Serial.begin(9600); } void loop() {  for (int i = 0; i <= 100 100; i++)  {    sensorvalue="sensorValue" + analogread(sensorpin); delay(1);  }  sensorvalue="sensorValue/100.0;"...

  • thingSoC I2C Hub
  • Instructions     from thingSoC I2C Hub
  • The default address for the I2C hub is 0x74 with A2 shorted, and A1 and A0 Open.0 = Shorted, 1 = Open (ie. inverted...)A2 A1 A0 - I2C Address1 1 1 - 0x701 1 0 - 0x711 0 1 - 0x721 0 0 - 0x730 1 1 - 0x74 (Default I2C Address as shipped)0 1 0 - 0x750 0...

  • Uploading the code
  • Instructions     from Arduino Controlled Safe (Locker)
  • *** FIRST DOWNLOAD AND INSTALL THE PASSWORD AND KEYPAD LIBRARIES *** JUST EXTRACT THEM IN ARDUINO LIBRARIES FOLDER Install the above mentioned two libraries. You can download them directly from the library manager or you can download the zip file and...

  • Free run (optional)
  • Instructions     from 68020 minimal homebrew computer
  • Although optional, it is highly recommended to test the board so far with the free run test. Connecting the databus to the ground, the CPU will read in 0x0000.0000 as an instruction and will execute a kind of NOP (in fact, it will execute ORI.b #0,D0)....

  • Wiring Up the Octosonar
  • Instructions     from HC-SR04 I2C Octopus "octosonar"
  • The connections on the Octosonar are clearly labelled. I'll try and run up a wiring diagram later, but for now the following list of connections should get you there. To connect to Arduino Octosonar PinUno Pin DefaultDescription5V5V5V supply for...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday