2552 Results for "8-bit cpu"

8. Field testing
Instructions from Elephant AI
Unfortunately, we have not been able to complete this testing in time for close of Hackaday Prize! But I'm sure once housing is completed, we can go ahead and do it! Some of the WWF researchers have offered to field test the prototypes, so I'm going...

Linkages/Components - Step 8
Instructions from MiniHawk VTOL
Form the elevon control rods by creating an L-bend 45mm from the threaded tip of the pair of 2-56 link rods used. Test fit the retaining Du-Bro E/Z Links 0.72 (2-56) Retainer Clip for each bend, and modify the bend as needed and cut flush. Alternatively,...

8: Configure tasmota software
Instructions from ESP and WS2812 based clock
Find the ip-adress of the esp. - this can probably be done in your routers status pages - or if you leave the esp in the programmer and boot it up while you are in a serial terminal it will show you its ip-adress Use a browser and go to the...

Electronics/Finishing - Step 8
Instructions from MiniHawk VTOL
The Center-of-Mass for the aircraft is intended to be at 165mm back from the tip of the nose, or 40mm back from the leading edge of the wing. This is exactly along the middle pair of mounting holes for the Battery Tray. This is an initial value, and...

#8 Assembly: feeder
Instructions from E-TKT: anachronic label maker
The feeder is a springed mechanism that helps the cog gain traction against the tape by gently denting the adhesive liner. Feeder + bearing surround 2x 623ZZ bearings with 2x washers, one on each extremity;slide them into the...

Step 8: The handle
Instructions from ⚡Thor's hammer⚡
There we started: a simple handle of 15 cm made of grey PLA by 3D printing. - second version: we then thought, that it could be nice to reproduce the "metal rings" of Thor's hammer. Then we thought: why not create those rings with real aluminium...

A bit of tinkering required.
Instructions from R.O.B. ROBOT HACK
You have to look for the motor control chip on the robot's board, located in the base. Then apply 3v to each pin on the chip to map out which pin controls which motor, and in which direction. Once you have this information, you can solder wires between...

8. Clear access for PCB
Instructions from 6-Axis Micro Manipulator
Move the legs out to allow access for fitting the PCB to the frame.

Step 8: Open the GUI
Instructions from Power Analyzer based on a COTS Power Monitoring IC
If you have installed python3.9 or greater, you can just run pip install -r requirements.txt and then python3 main.py

Drill a 3/8" hole in the bottom.
Instructions from beer can microphones
This is for the guitar jack. Note: you don't have to put it in the bottom if you don't want. Also note: a conical bit works wonders for this as opposed to an increasing series of drill bits.

Step 8: Adding the Steppers
Instructions from OpenBraille Steam
The steppers are mounted to the board with the NEMA_support. The support has two holes for M3 screws. Screw the support into the stepper and insert the coupler into the shaft. I got the wrong kind of coupler so I had to put shrink tube for them to fit...

Download my 32-BIT-MIPS.circ file
Instructions from MIPS32 Built in Logisim-ITA
Download the .circ file and import it into Logisim.

8) Apply the furnace cement
Instructions from Arcus-3D-C1 - Granite heated bed
Carefully tape off the groove for the thermistor and both end pockets so you don't get cement in them yet. Cut the end off your tube of furnace cement and fill each groove. Use a fair amount of pressure when doing this so you don't have any...

Step 8: Prepare for Drawing
Instructions from Wall Drawing Robot, Open Source
After hang robot on wall, we need to do calibration step by declare to Arduino code the distance of two nails. Then, we will prepare drawing as steps: 3.1 Your Picture need to draw 3.2 Convert picture to vector (*.svg file) by CorelDraw (or any other...

Step 8: How to Use
Instructions from Maker Your Own Professional Bench Power Supply
All Black stands for GND / -VeAll Red stands for Vcc / +VeAt the input we have to connect one of the +Ve voltage( 3V3/5V/12V)At the output we can connect the DC Device.The voltage and ampere of the device can be monitored on the digital using Output...

|<
<
3
4
5
6
7
>
>|