Close

775 Results for "%3E%EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8o%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F %E2%88%82%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC %EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5%3C %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1 %EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC%C2%B1%EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1 %2B%EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5%E2%88%81 %EA%B0%95%EB%82%A8%EC%85%94%EC%B8%A0%EB%A3%B8%E2%88%83 %EA%B0%95%EB%82%A8%EB%A3%B8 %E2%88%80%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E2%88%88 everything"

  • 68000 Processor

  • Plug in the 68000 processor and minimal glue logic. To test if you build this part of the circuit correctly, add 10k pulldown resistors on all 15 data lines of the processor.  Power on the board, and verify with an oscilloscope that A0 operates...
  • Assembly Steps

  • Print enclosure and file down inner tracks so that the joystick PCB slides in easily De-solder pins from joystick breakout board Use wires to make the following solder connections: Solder GND on Joystick to GND on Arduino Solder 5V on Joystick to VCC...
  • Step 6: Arduino Codes

  • The platform's construction is complete. However, our project still need code to function. This code should be uploaded to Arduino:#include //defining Servoss #define TOLERANCE 10 #define STEP_DELAY 7 Servo servohori; int servoh = 0; int servohLimitHigh...
  • Build and Initial Testing

  • First prepare all the parts for final assembly. Solder the pins to the Nano board if needed then install the Nano board to the I/O expansion board. Then, attach or solder the jumper wires to the button switch and the buzzer. I used some leftover servo...
  • thingSoC I2C Hub

  • The default address for the I2C hub is 0x74 with A2 shorted, and A1 and A0 Open.0 = Shorted, 1 = Open (ie. inverted...)A2 A1 A0 - I2C Address1 1 1 - 0x701 1 0 - 0x711 0 1 - 0x721 0 0 - 0x730 1 1 - 0x74 (Default I2C Address as shipped)0 1 0 - 0x750 0...
  • Password Protected Lock

  • First, connect the 4X4 keypad to the Arduino; connect the first six pins on the 4X4 keypad with the A0 and A5 pins on the Arduino. Then connect the last two pins on the 4X4 keypad module to digital pins 3 and 2 on the Arduino. After that, connect the...
  • On The Go Coffee Maker

  • Program LinkitOne to Control the Coffee cup using Bluetooth android app.Attach the LM35 temperature sensor to A0 pin, Transistor base switch and Bluetooth antenna to LinkitOne.Thus LM35 reads the temperature and send it to android app through Bluetooth....
  • Connections

  • Connect the two pins from the Sensor to the two pins on the Amplifier circuit via hook up wires. Connect the Vcc from the Amplifier to the 3.3V pin on the Arduino and the Gnd pin to the Gnd pin on the Arduino. Now connect the Analog Data Pin to the...
  • Router Attack

  • 1. Connect buzzer to D7 and Ground2. Connect button to D6 and Ground3. Connect potentiometer to A0, 3.3v and Ground4. Connect battery to VIN and Ground5. Upload the code6. Print the case front7. Fit inside an Altoids can and you are ready
  • Understanding how to disconnect the speaker

  • moThe big black device in the middle of the printed circuit board (PCB) is the speaker (aka buzzer, or transducer). You can see a little slit in the one side where the sound comes out. There is a back side to the circuit board that you cannot easily...
  • Run a Program

  • // The load resistance on the board #define RLOAD 22.0 #include "MQ135.h" #include #include #include #define SCREEN_WIDTH 128 // OLED display width, in pixels#define SCREEN_HEIGHT 64 // OLED display height, in pixels// Declaration for SSD1306 display...