138 Results for "Q 안산블랙잭 CDDC7_CОM ◆보너스번호 B77◆수원장안 프로토 구매๏토토핫픽⏬온라인황금성༈FX매매⋍안산블랙잭애용 thorough/"

Hackaday Juice
Instructions from Hackaday Juice
Now it sits. Leave it alone, undisturbed and out of direct sunlight. Make sure it is sitting in a place that is between 68° and 85.° After 7-30 days it will be ready. The amount of time required depends on the type of taste you prefer. Younger...

Sub $200 PCB Mill that doesn't suck!
Instructions from Sub $200 PCB Mill that doesn't suck!
Printing the parts:Please use a slicer that supports calibrating holes properly. I use KisSlicer for slicing, there is a free version available that supports printing one type of part at a time. You may print multiple of them at once but only the same...

Soldering
Instructions from Binary Wrist Watch
The very best way of keeping a circuit board still while soldering is with your old friend: masking tape. A couple strips will keep the PCB dead still while you wave around the soldering iron. I started with all the components with the lowest profile...

A "smart" speaker
Instructions from A "smart" speaker
I installed the actual version of raspbianwith apt install: motion fetchmail detox mplayer ripmimeHere is the link how to set the mail reception:https://www.axllent.org/docs/view/gmail-pop3-with-fetchmail/And the relevant part of motion config:#############################################################...

Run a Program
Instructions from Measure water Flow Rate using Arduino & Sensor
volatile int flow_frequency; // Measures flow sensor pulses// Calculated litres/hour float vol = 0.0,l_minute;unsigned char flowsensor = 2; // Sensor Inputunsigned long currentTime;unsigned long cloopTime;#include LiquidCrystal lcd(12, 11, 5, 4, 3, 9);void...

Create the main.c from this template:
Instructions from Simulate U8G2 on PC!
#include "u8g2.h" #include u8g2_t u8g2; int main(void) { int k; u8g2_SetupBuffer_SDL_128x64_4(&u8g2, &u8g2_cb_r0); u8x8_InitDisplay(u8g2_GetU8x8(&u8g2)); u8x8_SetPowerSave(u8g2_GetU8x8(&u8g2), 0); u8g2_ClearBuffer(&u8g2); for(;;) { u8g2_FirstPage(&u8g2);...

Identifying the joints
Instructions from Simulate your CAD model of the Robot in ROS
I have modelled a simple, small 3D printable robot. And the end effector is an open end at the moment. The 6 joints are visualized in the picture above. It’s generally good design practice in a design of this sort to use different subassemblies for each...

How to correctly mate the joints in the Solidworks
Instructions from Simulate your CAD model of the Robot in ROS
Since all the joints are revolute joints, in this case only mates that is utilized are coincident and concentric mates. The base joint, you could either make it fixed, or you could constrain it to the assembly planes with coincident mates (utilize the...

Programming and running the codes
Instructions from Remotely control a DC motor with Toit's PubSub API
1) Python API First, we’ll set up the Python program through which we’ll be sending the motor commands. Toit provides a publicly available gRPC API with API packages and examples for languages including Java, Python, and NodeJS. Follow the Python API installation...

Fourth meeting
Instructions from Analog meter Arduino Clock
If you were able to get all the magnets glue in at the third meeting everything will be wrapped up at this meeting. If you were not able too, then we will need to have a short fifth meeting. I do the same steps as the Third meeting. Skip...

▇▇▇▇ State Minimization (and Should You?) ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
Remember the coin example from earlier? You could have a state that shows you had a dime and a nickle and another state for a nickle and a dime. But it was smarter to have one state for 15 cents. This is an example of state minimization. If you were...

Python Code IRC Twitch Bot!
Instructions from Snap Like You're Thanos!
The files for this code is hosted in the files section of this project. Lets just start by importing the Socket, time, random, and math libraries. import cfg import socket import time import random import math They cfg file is one custom made with your...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
The 74HC595 can only do parallel output, so I used a 74HC165 to measure the state of the buttons via 4 current limiting resistors and send this information to the Arduino. More info about the chip can be found on its datasheet.The 74HC165 has the following...

EDID Inserter
Instructions from EDID Inserter
Before plugging in the freshly minted EDID Inserter (my last picture shows one dangling from a "3 in 1 Display Port DP Male to HDMI/DVI/VGA Female Adapter" off eBay, the case of which could also house our EEPROM of course),check that the sink with the...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
Control Panels Parts:MAX004 IP67 Hard Case – 350 x 230 x 86H mm MAX004S 2 of MAX001 IP67 Hard Case – 175 x 115 x 47H mm MAX001S 1 of Arduino Mega 2560 Adafruit Feather 32u4 FONAAdafruit Audio FX Sound Board - WAV/OGG Trigger20 x 4 LCD display Hackable...

|<
<
4
5
6
7
8
>
>|