582 Results for "%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%EC%96%B4%EB%94%94%E3%80%8Coptime4%2Ccom%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC %EB%8C%80%EA%B5%AC%EB%A7%88%EC%82%AC%EC%A7%80 %E3%80%8D %EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%E1%99%9C %EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%EA%B1%B8%E1%99%9C %EB%8C%80%EA%B5%AC%ED%9C%B4%EA%B2%8C%ED%85%94 %EB%8C%80%EA%B5%AC%ED%82%A4%EC%8A%A4%EB%B0%A9 %ED%83%80%EC%9E%84"

Attach network cables and peripherals
Instructions from Private Communication for Activists
For the initial setup, you will need to connect a monitor, keyboard, and (optionally) a mouse. Once the software has been installed these will no longer be necessary. You will also need to connect the box to the internet. There are two main scenarios:...

FPGA + 3 R + 1 C = MW and SW SDR Receiver
Instructions from FPGA + 3 R + 1 C = MW and SW SDR Receiver
GitHub hosts the complete project, it should be ready to synthesize and flash. Lattice Diamond 3.11 for Windows is the toolchain I used. There is a Linux version for it. Connect the secondary UART channel to pin 73 and 74 by shorting R14 and R15 on the...

Pneumatic Extra-thumb
Instructions from Wearable, Soft Robotic Exoskeleton Gloves
The soft telescopic, extra thumb actuator is based on a urethane rubber (Smooth-On Vytaflex 40) structure designed for grasping assistance during the execution of ADLs. The foldable structure was designed in such a way that it does not influence grasps...

Intercom box and speaker box
Instructions from A P100 Mask Intercom
The following is a chronological series of pictures meant to compliment the circuit diagram and parts list. Breadboard version of project Perfboard version of the project Boxed version, internal; the battery is nickel-metal hydride type, 9V. It...

Technical Specifications and Applications of the Sensor
Instructions from Capacitive Fingerprint Sensor with Arduino and ESP
The Technical Specifications of this Sensor are as given below:- Operating Voltage: 3.3V Operating Current:

Acrylic Box Assembly
Instructions from 2600 Magazine Storage System
I designed small 3D printed corner pieces to hold the acrylic sheets at a perfect 90 degree angle, and used blue painters tape to pull them together tightly. Using a syringe, I ran a small amount of Weld-On 4 down the length of the joint from...

SAMD21 + QUECTEL L80 GPS
Instructions from Atomic Synchronator => TicTacSync
For now, I'm building TicTacSyncs with off the shelf boards, here an Adafruit Ultimate GPS FeatherWing (25 USD) and a Adafruit Feather M0 Basic Proto (20 USD): Flash the board using the Arduino IDE with this program: ppssyncYears.ino A motivated maker...

Upload and Execution
Instructions from Ameba Arduino: Use Ameba as Server to Send Status
Upload the code and press the reset button on Ameba. After connecting to WiFi, Ameba starts to run as server. The IP of the server is shown in the serial monitor, and port is 80. We connect to the server in a browser, and we can see the data sent from...

Picking up the pieces
Instructions from Well well
Part Substitutions Z8F0822, can be used in place of the Z8F0812HC-05 is optional. Also, the HC-06 should work with no changes to the layout or codeNearly any 3.3V low dropout regulator can be usedJust about any phototransistor should workThe same goes...

Construct the Mic Enclosure
Instructions from SASS-style Stereo Microphone for Nature Recording
Put the enclosure together using all the parts except the Back. You will need to leave the Back off to install the microphones and carpet padding. Use some rough (80 grit) sandpaper on the surfaces that will be glued, especially the uncut surfaces...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebServer Sketch ===// PCF8574 WebServer, listens for /inline?state= // Hari Wiguna, 2016 #include #include #include #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebClient Sketch ===// PCF8574 WebClient, watches buttons and sends /inline?state=x to WebServer // Hari Wiguna, 2016 #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

Step 1: 3D printing
Instructions from UltraTower
To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket". You can download the files...

Step 1: 3D printing
Instructions from UltraTower 2023
To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket". You can download the files...

|<
<
5
6
7
8
9
>
>|