Close

4829 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워㉵ 강남쓰리아워rest강남쓰리아워ル쓰리아워가격obs 강남술집정보ㅈ쓰리아워가격¤강남쓰리아워Ｉ─쓰리아워가격minute"

  • Section #6
  • Log     from Apollo Saturn V and LUT
  • Looking ahead: Only 6 more levels split between two sections remain along with two more swing arms plus the DRRS and of course the crane. The legs and floors from this point on will have to be redesigned to make them lock together better. The vertical...

  • Swing Arm #8
  • Log     from Apollo Saturn V and LUT
  • Swing Arm #8: For all the arms I suggest keeping the bottom off until you get the lights installed to give room for soldering. For this swing arm all the wires and pipes run inside the arm so keep the bottom plate off until you are ready to mount the...

  • Section #7
  • Log     from Apollo Saturn V and LUT
  • Motor Housing: The motor housing is complete except for the stairs. In the first picture you can see the floor beams with the grating cut to shape. I didn't make a specific grating. Just print up the standard grating and then cut out the hole shown....

  • Swing Arm #9
  • Log     from Apollo Saturn V and LUT
  • All swing arms have common parts except SA9. After drawing up the new hinges I realized for some reason I made the side 4 support column way too narrow. A simple change to the width and a reprint gave a column that supports the new hinges, so I cut the...

  • Colby Crane
  • Log     from Apollo Saturn V and LUT
  • The Colby crane is the final, crowning achievement of the LUT.  The crane is going to be automated in that it will rotate and the hook will raise/lower.  Notice that I intended to use the crane model by CristineZ as is but the more I dug...

  • Hack Chat Transcript, Page 1
  • Log     from The Hoarder's Dilemma Hack Chat
  • Dan Maloney  3:00 PM OK, time to kick things off officially. I'm Dan, I'm modding today along with Dusan as we welcome Gabe Emerson to the Hack Chat Dan Maloney  3:00 PM Welcome one and all! Saveitforparts  3:00 PM Hi everyone! This is my first Hack...

  • Hack Chat Transcript, Page 2
  • Log     from The Hoarder's Dilemma Hack Chat
  • Sam Freeman  3:30 PM Simplify - I try to clean up the tools at the end of the day, even if I know I'll use it tomorrow Saveitforparts  3:30 PM I try (not always sucessfully) to put my tools and parts away before starting another project, but it doesn't...

  • Build the Wooden Keycap
  • Log     from Carpenter Tau Keyboard
  • In this blog post, we are going to build the wooden keycap! Review possible approaches You probably already familiar with a mechanical keycap. It is usually a thin, box shaped but with curves. On the backside, it has a cross shaped connector to fit the...

  • The beginning
  • Log     from New life to the Blaupunkt Berlin IQR 83
  • I got my Blaupunkt IQR 83 used, not working, and without history: It powered on and could play a tape, but the radio didn't work. My initial idea was to repair it but as I started looking into things, I realized that perhaps there was a better solution...

  • 5 december 2023
  • Log     from Ctrl+Fight!
  • On 5 December, we carried out a number of tasks. Firstly, we made cardboard prototypes of the boxes that will contain the sensors. These boxes will be sewn onto the bullet-proof vest. We took the necessary measurements to ensure that the boxes would...

  • December 29th
  • Log     from Ctrl+Fight!
  • We went back to school during holidays to print our boxes. After carefully rechecking the dimensions, and changing the thickness of the boxes, we launched 3D printing. We had smaller and larger boxes. Printing a small box took at least 4 hours (because...

  • January 5th
  • Log     from Ctrl+Fight!
  • After a week, we went back to school to get our boxes, since they take a long time to print. They were as we had imagined, except for one detail : the 3D printer had a large margin of error : we had not paid attention to this detail... This clearly shows...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday