2570 Results for "Y 대전 프로토 베팅 CDDC7.COM ▧프로모션번호 B77▧농구경기분석ϧ에스퍼홀덤℁KB손보👢메이저리그라이브중계ӈ대전 프로토 베팅애용 assurable/"

Using mice for X Y offset
Log from Simple & Cheaper CNC Shaper
In further investigation (thanks to PointyOintment's suggestion) it may be simpler to use multiple PS2 mice instead of the belts. You can do deadest reckoning with two mice read http://www.instructables.com/id/Optical-Mouse-Odometer-for-Arduino-Robot/step4/Further-Modifications-and-Finishing-Up/...

Milling the y-axis end plates:
Log from Building a Shapeoko 3 from Scratch
I have a feeling from now on the project will have slow but steady progress. So with that, let's take a look at the bit of progress I did get accomplished. I've done quite a bit of milling aluminum on my little X-carve, so cutting out a few profiles...

X, Y, Z Axis details - Part 2
Log from Monoprice Select Mini Electro-Mechanical Upgrades
Note 1: I capitalize "X-axis", "Z-height" and the like for legibility when scanning/skimming; pedants can hate me later.Note 2: This is where idealistic, that is mimal change for best outcome, modifications are. For measurements and construction details...

DRO Y axis progress and tool shopping
Log from Reviving a Shoptask 1720 XMTC Gold 3-in-1
I've started work on the Y axis DRO mounts, using Fortal alloy (7075 T-651 from ebay seller scottkrez). This is a material I have used before and I know it machines well and can be made very shiny. I'm on a learning curve with Fusion 360 and I'm on a...

[E2][M] The New Y Axis Slider
Log from SecSavr Sublime [gd0036]
Starting the new design Now I actually imagined that this slider would look a bit differently. I was thinking that I was going to have some additional fin that had a steeper angle than just extending the side curve for the bottom cover section....

Getting shared GPIO serial right, and other nuts to crack
Log from eForth for cheap STM8S gadgets
If you're following this little project you may have noticed that I take pride in adjusting the code for supporting almost any type of cheap STM8S Value Line device. Here is a number of constraints:in most cases UART pins are not broken outin some cases...

SNR Data for Eosin Y Study on 8/10/2016
Log from DAV5 V2.1 Spectrometer
Absorption and Emission of Eosin Y in EthanolThe first plot has the calculations that I used for determining the signal to noise ratio for my emission scan for Eosin YThe rest of this research note can be found here:http://publiclab.org/notes/dhaffnersr/08-12-2016/snr-data-for-eosin-y-study-on-8-10-2016...

X, Y, Z Axis details - Part 1
Log from Monoprice Select Mini Electro-Mechanical Upgrades
Note 1: I capitalize "X-axis", "Z-height" and the like for legibility when scanning/skimming; pedants can hate me later. Note 2: This is part one where measurements and construction details of the mechanical structure are listed. Idealistic modifications...

X and Y Mechanics Completed, Partial Z
Log from Laser Cut Mini Mill
I finished cutting most of the wooden parts and assembled them, I cut all of the linear rod and the remaining threaded rod. Most of mechanical assembly is complete. I put together an end stop based on the DarwinOptoEndstop for the X axis and hooked up...

The X and Y that were
Log from Minamil 2dc: a minimal CNC mill
The next rev of the XY table improves, I hope, in some respects other than looking good. So I took some beauty shots before gutting the first one. This seems like a good time to say a little about the mechanical design-in-progress. Telescoping...

Playing with 8 bit - fix_fft
Log from VU-meter Esp8266 - WS2812B
Here is a snippet on how to play with the fix_fft in winamp. The reason for this is, it gives a good idea if it's worth the effort to implement in the Esp8266 ( which I think it is ;-). It's just a quick & dirty hack... to get a feeling. Current goal...

So it begins... Which magnetometer?
Log from Aurora Observatory
This project is something I've had on my mind for a while. Mike Szcys posted to Hackaday with 4 days to go to the deadline for the hackaday prize, convinced me to formalize the idea and begin work, now I have to work fast !The prerequisite knowledge...

Marlin! (Round 2)
Log from Lerdge 3d Printer Mainboard Hacking
First off, some clarifications from discoveries since the last log:1. The USB B /CH340 and ESP8266 share the same USART, Serial1. This is why plugging in USB kills the ESP - they didn't want conflicts.2. I've had no success getting USB working through...

6. Testing The Water Sprayer System
Log from Smart Insect Repellent System
In this section I will show you the programming of the Nicla Vision, and the MKR WAN 1310 in the Water Sprayer system. We will also test the prototype. Programming The Nicla Vision Below I show you the code for the Nicla Vision board:# AUTHOR: GUILLERMO...

|<
<
3
4
5
6
7
>
>|