68080 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Tinymovr R3.3 (alpha2) now available!
Log from Tinymovr Motor Controller
Good news, after an admittedly long wait, the new alpha2 boards (R3.3) are now available! These boards have a few layout improvements compared to the alpha1 boards, namely: Better signal routing allowing wider power traces on the rear side of the board....

Chains, sprockets, shafts and bearings
Log from Woody the Electric Four Passenger Bicycle
woody is using BMX cranks because they allow very small sprockets. Below is one of two assemblies before welding. The bottom bracket was turned on the lathe, and the two plates were made by sendcutsend. And here it is bolted in place. The holes...

Context is everything
Log from Hackaday.bash.org
Courtesy of Ars:

Dynamic interactive design week 14
Log from Dynamic interactivity final project
everything almost done but some of the key doesn’t work very well

End of Line
Log from Chitu 3D Printer Mainboard Hacking
Everything is merged. Marlin auto-builds for the Tronxy (chitu) boards. And this log concludes this project. Happy hacking, everyone.

Starting to work put where everything goes
Log from PiBox
First view of the bits to include

A guide on powering Pi Zero directly from LiIon batteries
Log from ZeroPhone - a Raspberry Pi smartphone
At the project's beginning, when I was writing the "Features" section in the project's description, last entry was "Tons of Pi Zero-related hacks that were discovered along the way, that I'll share with you as the project goes =)". I didn't actually...

Prototype: Ready for testing
Log from KAPCOM
I finished mounting the hardware in the enclosure and wired everything up. I did a quick test of the displays and everything seems to be working. I don't have time to start testing tonight unfortunately.

Log 6 - Modifications
Log from Rock Em Sock Em Robot
After having printed another robot, it still couldn't fit our accelerometer. So we decided to change the design completely. Then printed it, and everything fits. We finished the code as well, so now everything needs to be assembled. We also cut...

Donor Cabinet work
Log from Star Trek: The Mirror Universe Pinball
7/29/2013: As I stated; been working on the cabinet for the Mirror universe project. I bought a couple of "project" Bally Star Treks from a fellow pinball collector out of Shertz a few years ago. These have been setting in storage for a while... and...

Prototype Board Design#2
Log from InterNoC
In this log, the first renders of the pcb layout are presented and a major change in the design. First off, the change was that we changed the FPGA package as obviously the 484 pin was an overkill for this design. The package was switched for the 256...

The history of SMP and some shoutouts
Log from Semisolid Metal Printing
The first attempt at this type of printing was done by someone on the Lulzbot forum back in 2013. Back then they didn't give any particular consideration to the material properties of the molten metal, which is why they couldn't get past the clogging...

Sophie Rises Up
Log from Home Robot Named Sophie
I have the budget to finish out the robot. I have the base aluminum panel, the 6 axis arm and the linear actuator/slide mech for the raising and lowering of the arm at ~12" with a future capability of 18". The arm raise mechanism took a lot...

Initial Checkout
Log from Intel SDK-85 Enhancements
What Is It?The Intel SDK-85 is a single board computer trainer from Intel. It is very similar to the MOS (later Commodore) KIM-1 in that it features a keypad and 7 segment display. 2K of ROM and 256 bytes of RAM are provided...

Topic 1: Fundamentals
Log from High Speed Digital & Mixed Signal Design
There is a major limitation with circuit schematics: 3 circuits (with the same schematics) may have significant performance differences which are a result of the physical layout of the circuits. Therefore it can be said that how a circuit is implemented...

|<
<
1
2
3
4
5
>
>|