19701 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워ｈ 쓰리아워worship쓰리아워레깅스룸쓰리아워가격강남쓰리아워egypt 강남술집정보クＱ강남쓰리아워disorder"

New V1.2 boards arrived incl. footprint fail
Log from µPower (beehive) SD logger
Update 12.06.18 - pics of the new board Not much cleaning done so far. They'll get their proper isopropanol cleaning when fully populated! top side with 18650 cell (LG-2) bottom side ---------- more ---------- Just soldered one of the new boards and...

Tinymovr
Log from Ø32 BLDC Controller
Found out about the Tinymovr motor controller. Basically what I'm trying to do! Very cool, and my version 2 will use it as reference. I hope to make mine even smaller (27x27mm vs 40x36mm) and cheaper ($40 vs €89). I only need up to 13V (3S lipo),...

Parity with Fibonacci
Log from PEAC Pisano with End-Around Carry algorithm
One thing that sets PEAC apart from the Fibonacci and Pisano series is the parity, or mod 2 remainder. When you take the natural sequence 0, 1, 1, 2, 3, 5, 8, 13, 21, 34, 55, 89, 144, 233, 377, 610, 987, 1597... The mod 2 is 0, 1, 1, 0, 1, 1, 0, 1, 1,...

MiCS-VZ-89T a low power air quality sensor
Log from Portable environmental monitor
Putting everything together also requires checking everything separately first. So I did with the MiCS-VZ-89T sensor, and here is the story, also presented on my blog: MiCS-VZ-89 Air Quality SensorA low power sensor that can measure at the same time...

Breaking AES using a $90 Development Board + OpenADC
Log from ChipWhisperer®: Security Research
Long ago when I started prototyping ideas, I was using a $89 FPGA Board (Avnet LX9 board). The ChipWhisperer system has always supported this board, but it's not as well documented as my newer, fancier hardware. I wanted to make a log post to demonstrate...

No officer, it's not a bong. I swear.
Log from Mk 16 Capital Ship MDM
Morning update: April 13, 89 PDAfter a long night of fighting with 123D make and my 3d printer, we have our first put together. To see very bad pictures of the Main Power/Data Bus (MPDB) look at step 2 of the instructions. After getting put together,...

MORE RADII!!
Log from Hubsan X4 Replacement Frame
I haven't putzed about with the v0.1 base at all, but I think I've got a motor mount design that I like. It's got the split bolt setup for securing the motor (including a cutout for holding a 2-56 nut), and the legs are cool lofted dealies. Lots of radii...

Fibonacci
Log from Gigatron TTL microcomputer
With the ALU verified and the RAM connected, today the breadboard determined that the first 8-bit Fibonacci number is 144. 0000 0000 ld $00 ; outer loop 0001 c200 st [$00] ; a=0 0002 0001 ld $01 ; b=1 0003 fc0a bra $0a 0004 0200 nop ; (pipelining) 0005...

Log #89 - CondomBoard specifications
Log from Internet of Condoms
Size: about 50x50mm (size of condoms I have, could be a little larger if required)Layers: preferrably a single 2-layer PCB, for easier ordering at the usual suspects in ChinaConnections: debug UARTMicroUSB for charging the batterytemperature sensor connectortwo...

Housing selection
Log from tv-remote-elderly
Requirements Easily found when misplacedBig enough to hold easily but not too big that it's cumbersomeShould have a battery compartment so that unskilled personnel can replace batteries without having to open up the housingRoom enough for the necessary...

FlexSEA-Plan
Log from FlexSEA: Wearable robotics toolkit
FlexSEA-Plan is an embedded computer used for high-level computing. It boasts a powerful processor and can run an operating system such as Linux. Developing code on this platform is similar to the regular (i.e. non-embedded) software development process....

All Your ISA Belong to Me!
Log from DDL4-CPU
Before I began the layout of the DDL4-CPU, I came up with an initial Instruction Set Architecture (ISA) for the design. It went through several revisions as I was designing the boards and refined the components. Here at the last minute as I am...

Initial LED Selection
Log from E-Bike Light
When I set about this project the first thing I wanted to work out was what LED I was going to use, as this would drive the requirements of everything else in the project, driver, lens, heatsinking, etc. Due to personal preference I decided that I wanted...

INFORMED HEX DUMP
Log from WIERD PROTOCOL
66 03 60 4D F5 66 03 C0 SOH DE 1D 40 E5 #62 E7 41 EE 70 48 4F 52 50 43 35 33 32 34 37 36 19 06 22 06 22 SOH10 46 30 46 19 SOH42 70 40 40 40 40 40 40 30 30 31 38 30 33 35 33 32 34 37 36 4B 08 08 DC C1 C1 32 DC C1 C1 32 42 B4 42 B4 02 SOH02 02 02...

Diving in with Calamity and Confusion
Log from Voyage 200 Upgrades
On my TI-89, one of the battery contacts on the PCB was heavily corroded and it took a good deal of time and heat to reflow solder to make a new pad. I did this to the V200 as a preventative measure too, but I guess I heated up the nearby fuse to where...

1
2
3
4
5
>
>|