45099 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격ｕ 쓰리아워가격earth강남쓰리아워강남쓰리아워쓰리아워enter 강남쓰리아워ぶЪ강남쓰리아워most"

I must fly...
Log from ML Clip Cam
In 5 daysThis is a distraction from writing the Pelicam software but days off and nice weather, have to flyI'm going to at the very least build a crude 1 day thing that functionsIt is pretty much just a battery-powered rpi cam... but it will be attached...

Week 1 & 2 - PCB Layouts
Log from 25in24 Electronics Project Board
I've started by laying out the five boards in Eagle 9.52. Boards are now being ordered through JLC. All parts have been ordered through Mouser and Digikey - however sourcing a small meter and solar panel that will match have been a bit of...

Week 3 part 2 - testing
Log from 25in24 Electronics Project Board
Well, initial testing was more difficult than expected - took about five hours just to get a couple of basic circuits working. Made a number of incorrect assumptions / mistakes including:Assuming it might be differences between components (germanium...

Rev1 Preliminary Accuracy and Precision Test
Log from Multimeter
As the title says, this is a preliminary test of the first version of the multimeter. Before the test, I basically calibrated it using my Fluke 101 as a reference. The results of the test are as follows: 2.5V Error: 0.569, Coeff of Var: 0.0102 5V Error:...

Rev1 Display Bodge
Log from Multimeter
To make the display work on revision 1, I bypassed the display driver and wired the pico IO pins strait to the segment LEDs. It is a little faint, as the display driver circuit worked completely differently, but it works to test the display.

Frankenscope
Log from Low-Cost Microscope Boom
There's not much to this build: Mount the monitor arms to your bench. Follow the manufacturer's instructions, or wing it like I did. I figured out where I wanted the scope to end up when in use and marked the location on my bench. Used a 1.5" hole...

Prerequisites and software
Log from VGA videocard for microcontrollers
Sometimes, when making your own devices on microcontrollers, there is a need to display huge amounts of information on a display and to use a bigger screen for ease of perception. Unfortunately, there are no ready-made and budget-friendly solutions for...

From prototype to product creation
Log from VGA videocard for microcontrollers
First of all, you should pay attention to the ROM used. The flash-ROM chip from an old computer motherboard has a finicky parallel interface where the address is written in two runs. This complicates the operating logic and increases access time. Additionally,...

Step 1:hardware
Log from Weather Station With A7670 -- Remote Monitoring
Insert the SIM card into the slot on the back of the boardConnect 0.96 OLED to Maduino Zero 4G LTE(CAT1 A7670) 's SCL and SDA;Connect Temperature and humidity sensor's data pin to Maduino Zero 4G LTE(CAT1 A7670) 's D6;Connect Photosensitive...

Step 2: Firmware about sensor
Log from Weather Station With A7670 -- Remote Monitoring
At first, we need to prepare the environment for ESP32 development board programming in arduino, and you can cheak this guide.This is a library for our Monochrome OLEDs based on SSD1306 drivers. #include This library allows you to communicate with...

Step 4: Firmware about LTE
Log from Weather Station With A7670 -- Remote Monitoring
Using HTTP(S) AT Commands, accessing to HTTP server,SerialUSB.println("Maduino Zero 4G LTE CAT1 Test Start!"); SerialUSB.println("Wait a few minutes for 4G star"); delay(3000); sendData("AT", 1000, DEBUG); delay(5000); sendData("AT+CICCID", 1000, DEBUG);...

Nowhere Near the End
Log from Longer LK5 Pro Delirium Build
My linear rail shipment got delayed by 10 days. I ordered the wrong M3 T-nuts and needed to get non-rotating ones. Luckily those arrive today.I'm missing 9 screws and 8 washers and am currently waiting to ask a friend to get them.I still don't have...

Schematic
Log from "Perpetual" Wristwatch
It's have simple schematic, for save pins I used Charlieplexing(35 components in total): https://en.wikipedia.org/wiki/CharlieplexingIn this project i use for charging 12 light sensor BPW34S, on clear sun one cell make 0.5-0.6 V and ~2 mA, connect its...

Hardware and libs
Log from TinyML meets dog training
For my first trials I decided to use the TinyML kit: which contains Arduino Nano 33 BLE Sense and the OV7675 camera (kit). I use the following libraries on arduino IDE:Arduino Mbed OS Nano Boards v3.0.1Arduino_OV767X v0.0.2Arduino_TensorFlowLite (from...

basic protocol structure
Log from VEVOR diesel heater protocol
Some days ago a friend told me about the heaters from Vevor and after some search I found this page very promising: http://afterburner.mrjones.id.au/ So I hoped the Vevor ones have the same protocol structure and things would be quite easy....

|<
<
3004
3005
3006
3007
>
>|